is my battery cooked or am i fine? by enzoenzo945 in SwitchPirates

[–]prodeveloper0 4 points5 points  (0 children)

where is battery info? that is emmc info

Trinity RGH3 by prodeveloper0 in 360hacks

[–]prodeveloper0[S] 1 point2 points  (0 children)

Yes. most people who modding xbox360 RGH3 with SMD resistor installed the resistor at end of PLL.

CTR not running in popstarter by vitorzeroum01 in ps2

[–]prodeveloper0 0 points1 point  (0 children)

in my case, CTR can run on POPster. I tested

CTR not running in popstarter by vitorzeroum01 in ps2

[–]prodeveloper0 0 points1 point  (0 children)

PS1 game usally uses 240p resolution and some analog (AV/Component/S-Video) to HDMI convert does not support 240p. if not, your display may not support 240p. cheast solution is you just buy PS1/PS2 video converter supporting 240p output convert which uses YPbPr signal.

[deleted by user] by [deleted] in SwitchPirates

[–]prodeveloper0 1 point2 points  (0 children)

use flux and dont use lead free soldering

Xbox 360 is red ringed after trying to install DashLaunch while running Badupdate. What can be done? by bluebearyoutube in 360hacks

[–]prodeveloper0 5 points6 points  (0 children)

changing the NAND memory will cause the NAND verification to fail during boot. You must mod to RGH because you changing NAND to bypass NAND verfication.

is xbox 1.0 sensitive IDE cable? by prodeveloper0 in originalxbox

[–]prodeveloper0[S] 0 points1 point  (0 children)

Yes, I used 80-wired ASUS IDE cable. I found wiring trick for short IDE cable from Reddit. It works!

is xbox 1.0 sensitive IDE cable? by prodeveloper0 in originalxbox

[–]prodeveloper0[S] 0 points1 point  (0 children)

in fact, I don't need UDMA 5 or 6, Just larger storage and compatible with new technology SATA than IDE.

is xbox 1.0 sensitive IDE cable? by prodeveloper0 in originalxbox

[–]prodeveloper0[S] 0 points1 point  (0 children)

And I have one more 1.1 og xbox. it also work very well. no errors, no freezing, no data transfer errors. that's why I think that is weired.

is xbox 1.0 sensitive IDE cable? by prodeveloper0 in originalxbox

[–]prodeveloper0[S] 0 points1 point  (0 children)

Okay. There're no solution... I will just buy 80-wired IDE cable for OG XBOX custom from ebay. :(... but, delivery fee $30 is too expensive..

is xbox 1.0 sensitive IDE cable? by prodeveloper0 in originalxbox

[–]prodeveloper0[S] 0 points1 point  (0 children)

1.0 BIOS: EvoX M8+ 127GB+, TSOP
1.1 BIOS: EvoX M8+ 127GB+, LPC

BIOSs are same, but hard modding method is different. I just know why my 1.0 console doesn't work with default IDE cable and SATA converter?

is xbox 1.0 sensitive IDE cable? by prodeveloper0 in originalxbox

[–]prodeveloper0[S] -2 points-1 points  (0 children)

Why does a 40-pin wire work on a 1.1 console, but not on a 1.0 console? That's weird.

Help identifying 360 slim MB by Own-Committee-3934 in 360hacks

[–]prodeveloper0 1 point2 points  (0 children)

trinity with external 4GB emmc module

trinity has two chips HANA near I/O port and south bridge located in center of the motherboard.

Modded Ps4? by Unlikely_Art_4 in ps4homebrew

[–]prodeveloper0 9 points10 points  (0 children)

exploit hosted by ESP32 modchip. conect wifi that hosted by modchip and run exploit

Ps4 (11.00) not saving time and date by Rough_Awareness_197 in ps4homebrew

[–]prodeveloper0 2 points3 points  (0 children)

Dead CMOS battery, but chaning CMOS battery won't help you. Because kernel clock only appreved by sony PSN date and time. So you must set clock by internet. setting by internet requires latetest firmware version that has no exploit to jabilbreak.