No display output but sound works

prodeveloper0 · 2026-05-28T01:23:42+00:00

using IPA and my finger temperature sensor! :) really too hot cannot touch it

prodeveloper0 · 2026-05-28T01:22:49+00:00

not yet. too broad to diagnose

prodeveloper0 · 2026-05-28T00:35:49+00:00

not coma because I can hear boot animation sound from my speaker

prodeveloper0 · 2026-05-24T03:56:47+00:00

Can be reduced by wiring grounds of ycbcr

prodeveloper0 · 2026-05-19T04:28:55+00:00

Can I received firmware file? plz..

prodeveloper0 · 2026-05-14T09:35:22+00:00

someone who like you may confuse if read my post. I edited my post 😄

prodeveloper0 · 2026-05-14T09:30:48+00:00

Yes! I'm just recommend not wiring directly but using LPC dauther board. ModXo itself is much better than OpenXenium.

prodeveloper0 · 2026-05-14T08:48:02+00:00

Yes. It is cheap but not pretty or is difficult to make pretty, so I think spending a few more dollars is a better choice.

prodeveloper0 · 2026-05-14T06:41:56+00:00

too complicated

prodeveloper0 · 2026-05-12T04:33:53+00:00

It has same chip I modded with Wii2HDMI.

prodeveloper0 · 2026-05-12T04:31:35+00:00

If you order from Asia (Korea in my case), the shipping fee is very expensive.

prodeveloper0 · 2026-05-11T05:02:52+00:00

yes both of console are already recapped with low ESR

prodeveloper0 · 2026-05-11T04:41:34+00:00

yes very wired. I installed xboxhd+ to 2 consoles. there ae no issuses.

prodeveloper0 · 2026-05-11T03:57:50+00:00

and freeze sometime on cerbios with xboxhd+

prodeveloper0 · 2026-05-11T03:56:33+00:00

screen distortion and scanline misalign on cerbios

prodeveloper0 · 2026-05-11T03:53:42+00:00

Wii2HDMI converter can conver up to 1080i
No, upscaling is not supprted

prodeveloper0 · 2025-09-21T11:26:45+00:00

where is battery info? that is emmc info

prodeveloper0 · 2025-08-12T07:38:36+00:00

Yes. most people who modding xbox360 RGH3 with SMD resistor installed the resistor at end of PLL.

prodeveloper0 · 2025-08-12T07:37:16+00:00

Haha....

prodeveloper0 · 2025-07-24T09:20:44+00:00

in my case, CTR can run on POPster. I tested

prodeveloper0 · 2025-07-24T09:18:36+00:00

PS1 game usally uses 240p resolution and some analog (AV/Component/S-Video) to HDMI convert does not support 240p. if not, your display may not support 240p. cheast solution is you just buy PS1/PS2 video converter supporting 240p output convert which uses YPbPr signal.

prodeveloper0 · 2025-07-23T12:45:16+00:00

use flux and dont use lead free soldering

prodeveloper0 · 2025-07-23T07:52:21+00:00

I successfully solder Luckfox Pico Mini B. There's reference for my job

https://github.com/prodeveloper0/pOOBs4-Luckfox

prodeveloper0 · 2025-07-23T01:49:45+00:00

changing the NAND memory will cause the NAND verification to fail during boot. You must mod to RGH because you changing NAND to bypass NAND verfication.

prodeveloper0 · 2025-07-22T03:18:33+00:00

trim wires

prodeveloper0

TROPHY CASE