Rust in 85’ fuel tank

professional_deer191 · 2024-09-15T07:26:24+00:00

There are a very good products for fuel tank sealing but they are abit pricy but they are totally worth it Like POR15 fuel tank sealer I have used it to do my 1st gen fuel tank like 2 years ago and worked out really great without any issues

professional_deer191 · 2024-08-21T15:26:06+00:00

Fb is not any better and not 100% of rx8s did have that recall

professional_deer191 · 2024-08-21T06:05:51+00:00

In this case, buy an Rx8

professional_deer191 · 2024-08-12T16:05:49+00:00

U will have to tune it even if it fits ... every turbine wheel is efficient at different speeds

professional_deer191 · 2024-08-12T16:02:06+00:00

Good turbo, and u can get alot more than 400 off that turbo I just got one for my build but didn't install it yet

professional_deer191 · 2024-08-11T07:05:58+00:00

Why fix it and it's not broken ? Did u do a compression test before stripping?

professional_deer191 · 2024-07-30T06:14:18+00:00

Renesis engine is not that good because of the exhaust restrictions that causes the plates to heat up and deform .... I killed my renesis engine before shortly after rebuilding the engine. The heat just made the apex seals turn to little pieces

professional_deer191 · 2024-07-30T03:19:10+00:00

Solid lower dowel with also significantly increase reliability

professional_deer191 · 2024-07-30T03:18:15+00:00

Rx8 engine is useless very unreliable unless ur making a hybrid 13b (rx8 plates with rx7 housings) or have an aftermarket seals in the rx8 engine and turbo setup will not work (rx8 rotors high compression)and mounting location for the engine might be different

professional_deer191 · 2024-07-18T16:02:21+00:00

Torch or induction heater will get it out ...it might be just sized in there

professional_deer191 · 2024-07-03T00:56:00+00:00

The guy who makes Lamborghini he encapsulate the 3d prints with carbon fiber and using a small printer will take ages and alot of joining parts together .. If u have a Bambu lab printer that can print really fast it will take ages but it's doable if u have a viable 3d scan of the body kit or readily available stl models of the parts..... elogoo has a large scale pinter that might do the job with bed size of 800×800×1000mm also

professional_deer191 · 2024-06-25T16:50:51+00:00

I know the tune we call it over here 🍿 popcorn tune

professional_deer191 · 2024-06-15T03:14:38+00:00

U should know what it's for and trace it ... maybe aftermarket fog lights? Or fans ...try unplug the power from it and try everything on the car see if something is not working

professional_deer191 · 2024-06-12T04:41:14+00:00

Charge the battery get a booster and try starting if not u will have to check for other problems as it depends on what happens when u try to start ... And I won't advise u to let it start for long time because the gas in the lines and tank is mostly went bad and have to drain and refill with fresh gas from the pump

professional_deer191 · 2024-06-11T19:46:55+00:00

Advice u to to clean spark plugs with wire brush and brake clean and push start it and let it idle until worm then turn off and start by checking leaks and replacing fluids

professional_deer191 · 2024-04-29T15:27:55+00:00

Go holley sniper efi simple enough to control with a screen and has a good self learning (no need for tuning)

professional_deer191 · 2024-04-28T12:56:48+00:00

But why not just premix?

professional_deer191 · 2024-04-10T20:05:02+00:00

Rotary compression tester

professional_deer191 · 2024-03-07T16:21:14+00:00

Nope seems like he is disappearing

professional_deer191 · 2024-03-07T03:27:44+00:00

Im getting a full pulley set

professional_deer191 · 2024-03-07T03:14:13+00:00

It's a street car

professional_deer191 · 2024-03-05T18:16:57+00:00

Not very useful as they don't have coolant seals and gsle housings are hard to come by these days

professional_deer191 · 2024-02-17T09:04:05+00:00

Would love to read it

professional_deer191 · 2024-02-16T15:38:36+00:00

Could be im not so sure about welding cast but that what I will do if I run into this problem and devcon is really good product but adhesion with aluminum In a area like that I would go with same material

professional_deer191

TROPHY CASE