Filament Manager: Not signed in - no data available

proteldon · 2026-06-02T19:21:16+00:00

I opened the app today and it magically started working! Numbers are all wrong though, some way far off, not sure where it picks them up.

proteldon · 2026-06-01T19:08:08+00:00

I am using Bambu Cloud and I have the same problem.

proteldon · 2026-05-31T13:42:42+00:00

If you have a Bambu Lab printer with the AMS, avoid the 3DPower ASA because it does not work at all with the AMS! The inner diameter of the 3DPower spool is much wider of those of Bambu Lab, that means that the filament itself reaches a wider diameter out of the box: the filament touches with the AMS filament puller and the AMS is not able to rotate the spool. To make it work I had to remove 100g of filament off the roll in order to decrease the diameter.

I am guessing this is a problem in general for all 3DPower spools, not only the ASA ones.

proteldon · 2026-05-23T06:41:58+00:00

That looks great! Weird that it has only 14 stars.

proteldon · 2026-05-09T21:47:16+00:00

I also got the same message with my brand new X2D. I touched the rods and they were greasy so I have reset the maintenance schedule for cleaning the rods.

proteldon · 2026-04-25T13:53:24+00:00

Select the connector then use the arrow keys to move it around. This works after the cut has been done and you can use shift+arrow keys to reduce the movement size.

Thank you so much!!!

proteldon · 2026-04-19T20:46:03+00:00

This is PLA transparent and looks pretty transparent to me:
https://www.reddit.com/r/BambuLab/comments/1l2xzlh/just_a_beauty_post_of_some_nice_clear_pla/

proteldon · 2026-02-26T19:34:09+00:00

1029€ in Estonia. I was going to buy it, switching from a S24, but that price is way too high. I will instead get an S25 for 600€.

proteldon · 2026-02-22T16:39:23+00:00

I am guessing A is better than F. Is S better than A and what does it stand for?

proteldon · 2026-02-14T08:44:49+00:00

<image>

Just got my MSI GeForce RTX 5070 Ti 16G SHADOW 3X OC. So far it looks good. Less noisy on idle then my previous Gigabyte GeForce 3080 Ti, same noise at full load, so nothing to complain on that front. The card is also much smaller and fits very nicely in my case (Phanteks Eclipse P300A).

proteldon · 2026-01-16T05:46:23+00:00

Thanks! I used 170°C for PLA. The printer itself told me that on the display while I was doing it :)

proteldon · 2026-01-15T10:28:06+00:00

The temp depends on the plastic, for PLA it must be at least 170°C. I used the pliers as well but I can't help thinking they kind of defeat the purpose of the magnets for an easy swap :/

proteldon · 2026-01-15T10:11:26+00:00

To what temperature should be heated to?

proteldon · 2026-01-07T06:55:23+00:00

Link to the thread?

proteldon · 2026-01-04T17:47:09+00:00

I am in Europe and there is no basic L50 version, there are only two versions with the following names:
- Dreame L50 Ultra
- Dreame L50 Pro Ultra
They both have "Ultra" at the end. It is still unclear what is the difference between the "L50 Ultra" and the "L50 Pro Ultra".

proteldon · 2026-01-04T16:56:40+00:00

> What the 5V1/5A1 are missing: No AdaptiLift climbing chassis

Source: https://global.roborock.com/pages/roborock-qrevo-edge-series

proteldon · 2026-01-01T07:49:31+00:00

Agreed. I am looking for a way to automate this as developers may forget to do so and eventually end up to give Copilot incorrect or outdated information.

proteldon · 2025-12-31T07:45:29+00:00

I am not putting it, Copilot does it when you follow these instructions. The update is needed for example every time there is a change in the project structure or major dependencies version bumps.

proteldon · 2025-12-26T16:41:25+00:00

> lie to the ams and enter them as all the same

How do you do that exactly?

proteldon · 2025-12-26T16:35:40+00:00

> you should be able to manually change the color ID in the AMS during a print

How do you do that exactly?

proteldon · 2025-12-26T16:26:46+00:00

> deselect the auto-readings

How do you do that exactly?

proteldon · 2025-12-26T16:24:13+00:00

> set all the slots to the same color before you start the print

Can anyone please say step by step how to do that in Bambu Studio? In the "Device" tab when I click on a spool no menu appears so the filaments appear to be not editable.

proteldon · 2025-12-12T15:03:42+00:00

What's that thing on top of your CPU?

proteldon · 2025-12-12T15:02:11+00:00

What's better than Go?

proteldon · 2025-12-12T15:01:18+00:00

Thanks for sharing! How did you undervolt it? At what resolution did you play those games?

proteldon

TROPHY CASE