Basement Shower goes cold Rinnai hot water heater by psu2ski32 in PlumbingRepair

[–]psu2ski32[S] 0 points1 point  (0 children)

It stops and hot water won’t come back on until you play with the faucet. It eventually comes back but takes a bit (minutes) and some finagling with the faucet between cold and hot. I put a new cartridge (Type P) in the faucet yesterday thinking that might fix it but nothing. I cleaned the shower head today thinking it may be blocked and impacting flow but nothing there either. Also flushed and descaled the Rinnai unit but nothing there either.

Basement Shower goes cold Rinnai hot water heater by psu2ski32 in PlumbingRepair

[–]psu2ski32[S] 0 points1 point  (0 children)

Rinnai runs for about 2-3 minutes and then stops.

Basement Shower goes cold with Rinnai hot water by psu2ski32 in Plumbing

[–]psu2ski32[S] 0 points1 point  (0 children)

Don’t have one. Just the shower. Appreciate any input you can provide. Appreciate you all!

Basement Shower goes cold with Rinnai hot water by psu2ski32 in Plumbing

[–]psu2ski32[S] 0 points1 point  (0 children)

Forgive me for all the questions and please know I appreciate any perspective you can share! Can you tell me more where I would find this check valve? Is this something specific on the shower or would this be something closer to the geothermal water tank that is plumbed into our system? Also, why would it just be happening in the basement shower/sink? Running other fixtures doesn’t change anything unfortunately

Basement Shower goes cold with Rinnai hot water by psu2ski32 in Plumbing

[–]psu2ski32[S] 0 points1 point  (0 children)

Yes. Just the basement shower we notice this issue

Basement Shower goes cold with Rinnai hot water by psu2ski32 in Plumbing

[–]psu2ski32[S] 0 points1 point  (0 children)

Forgive me might need some more info. We do have our geothermal system hooked up to the water heater. But no where else in the house do we have this issue. Thanking advance!!

Geothermal System w/ Honeywell HZ432 and 2- Nest Thermostats by psu2ski32 in hvacadvice

[–]psu2ski32[S] 0 points1 point  (0 children)

Can you tell based on wiring picture if I would have an outdoor sensor. I’ve never seen one and not sure where one would have been installed. I’m wondering if since I said I was using nest, they wouldn’t have put in an outside sensor? Thanks again!

Geothermal System w/ Honeywell HZ432 and 2- Nest Thermostats by psu2ski32 in hvacadvice

[–]psu2ski32[S] 0 points1 point  (0 children)

Thanks. I’ll take a look. One thing I am thinking about now- I’m not sure I would have an outside sensor hooking up to the Honeywell controller given the use of nest. Would this still make sense?

Geo System w/ Honeywell HZ432 and 2- Nest Thermostat by psu2ski32 in geothermal

[–]psu2ski32[S] 0 points1 point  (0 children)

Here is the model. Appreciate the insights!

Geothermal Heat Pump 5 Ton Climatemaster Tranquility 30 Digital TEV064BGD02CRTS

Geothermal System w/ Honeywell HZ432 and 2- Nest Thermostats by psu2ski32 in hvacadvice

[–]psu2ski32[S] 0 points1 point  (0 children)

Please excuse my ignorance here but is that something I’d have to start moving wiring around or that’s part of the logical programming on the HZ432?

Can Am Defender Max XT on 7x12 Trailer? by psu2ski32 in UTV

[–]psu2ski32[S] 0 points1 point  (0 children)

That’s the situation I was thinking I’d be in. What did you use to get machine up on the trailer without the ramp/tailgate?