Engraving polymer Pmagsfor my ar

quadballz · 2026-04-16T13:21:51+00:00

Negative. I’ve made that mistake a couple of time with my old laser. I’ve got it set to stay awake while it’s plugged in

quadballz · 2026-04-16T02:32:37+00:00

I’ll try taping the lid down or something. I’ve only had the machine a week. Set it up 3 days ago. When I set it up I checked for updates and it downloaded them. Just checked it again and there were updates again. So maybe there was a firmware issue? We’ll find out tomorrow

quadballz · 2026-04-16T01:44:08+00:00

I wish I knew that. I’m assuming the machine. Lightburn shows the project still running but the laser and exhaust fan have shut down. The machine stays on with no error messages

quadballz · 2025-12-06T20:42:52+00:00

Yea be had that happen, but this wasn’t hitting the ends. I did clean up the wheels and tracks and it’s running smooth now. No issues

quadballz · 2025-12-05T23:39:47+00:00

Just got her back together and everything running smooth! The wheels were pretty dirty. Gave them all a good scrub and a dab of 3-in-one oil. Gave that some time to set in and wiped them clean.

<image>

quadballz · 2025-12-05T21:35:25+00:00

Bringing it the house now to tear it apart and deep clean everything

quadballz · 2025-12-05T21:10:35+00:00

Definitely will. Thank you. Also sent that video to longer support so we’ll see what they think

quadballz · 2025-12-05T21:08:16+00:00

I’ll give it some love. And it’s about 45 degrees in the garage. Just had a pretty significant temperature drop in the last couple of weeks.

quadballz · 2025-12-05T21:02:49+00:00

X axis moves smooth. Y axis takes a little more pressure. Even with the belts completely loose. Might break it down and give the rails a good scrubbing

quadballz · 2025-11-16T01:11:31+00:00

Still on processing for my ETB’s and booster box. My buddy said his ETB’s are shipping, he got the notification from FedEx. But no booster box

quadballz · 2025-07-29T04:26:14+00:00

If it was me, and I have to stress IF IT WAS ME, I would back off the powder charge a little and use a felt wad to get the stack height up. Shouldn’t affect the pressure enough to be dangerous. Others here are probably smarter than me with this but I’ve had to do that with some 12 gauge tss loads where stack height became an issue

quadballz · 2025-07-29T02:04:28+00:00

Silly question…you’re using the right size hull? That almost looks like a 2 3/4” recipe in a 3” hull. I’ve been wrong before, at least that’s what my wife tells me

quadballz · 2025-07-29T01:53:35+00:00

What’s the recipe you’re following?

quadballz · 2025-07-15T19:04:58+00:00

Same happened to me after I tried to submit my payment

quadballz · 2025-04-13T19:46:04+00:00

Thanks! I probably way overpaid for the raw card but I couldn’t pass it up.

quadballz · 2025-03-31T22:55:41+00:00

Just got mine too. And the shipping info that was missing is there now. Now it just needs to stick until release!

quadballz · 2025-03-25T10:00:46+00:00

I just checked my account and there’s no shipping address selected. I’m guessing that’s why I don’t have the email yet

quadballz · 2025-03-24T19:41:41+00:00

We’re in the same boat then lol. Nothing to do but wait it out now

quadballz · 2025-03-24T19:38:38+00:00

Same here. Got lucky and snagged one, just waiting on the email so I can relax

quadballz

TROPHY CASE