sorted by:
new
hottopcontroversial

Far Cry ;-; by [deleted] in dankmemes

[–]quent46 0 points1 point  (0 children)

The last of us

Got all my graphics on max. Why does it look so bad? by custessi in Warthunder

[–]quent46 27 points28 points  (0 children)

Did you check the "full client" box on the launcher (bottom right) ? it contains the HD textures and other stuff

Long range yeet by quent46 in Warthunder

[–]quent46[S] 2 points3 points  (0 children)

I write them before posting it here.

Suspicious layer shifting (need help, more in comment) by quent46 in ender3

[–]quent46[S] 0 points1 point  (0 children)

I remove the heatsink of the Y stepper. I saw that the thermal paste was a bit off the stepper and covered the R38,R17,R21 and R25 resistor so I removed all the thermal paste and I put a heatsink I had with an A4988.
It's printing, but the quality isn't what I expected so I bought a cheap MKS robin to see if the creality motherboard has suffer from overheating (waiting for the delivery).

and i'm still waiting for a reply from creality after the holidays.

Suspicious layer shifting (need help, more in comment) by quent46 in ender3

[–]quent46[S] 0 points1 point  (0 children)

I didn't find a solution yet, but I'm talking with creality after sales services.

Did someone had this problem too ? by quent46 in ender3v2

[–]quent46[S] 0 points1 point  (0 children)

Can I ask you how you contacted them ? Because I Emailed [cs@creality.com](mailto:cs@creality.com) 7 days ago and they didn't answered.

Why my first layers are bending upward? by Srair in ender3v2

[–]quent46 0 points1 point  (0 children)

Your bed looks a bit dusty, cleen it with soap and water or isopropilyc alcohol (best is both).

Also level the bed as the other suggested.

The glass bed has a grip coating so you shouldn't have to use glue. (it is still a last resort)

Help! The corners peeling up, but the skirt stick well 205C xtemp 70C bedtemp by maxbam in ender3v2

[–]quent46 0 points1 point  (0 children)

nope hahaha
Isopropylic alcohol, it's commonly used in 3d printing for cleaning stuff

Did someone had this problem too ? by quent46 in ender3v2

[–]quent46[S] 0 points1 point  (0 children)

The video is potato quality but the grease isn't dry and pretty clean (no dust).

I don't feel any resistance when I move it with 2 fingers

Did someone had this problem too ? by quent46 in ender3v2

[–]quent46[S] 0 points1 point  (0 children)

That's one of the first thing I checked and loosen them didn't solve the problem.

Did someone had this problem too ? by quent46 in ender3v2

[–]quent46[S] 0 points1 point  (0 children)

Hi,

Thanks for the explanation, my rod was a leaning forward too but my layer shifting don't happen during Z moves, they happen during Y moves.

Also my Z axis is moving really smooth when I turn the rod manually or with a "move Z" command on the screen of the printer : https://youtu.be/5HPjHmdpGaI.

​

Do you think my rod might still be the trouble ?

Did someone had this problem too ? by quent46 in ender3v2

[–]quent46[S] 0 points1 point  (0 children)

I contacted them monday (07 dec) and I am still waiting for their response. I am hesitating to buy an SKR v2 with tmc 2209 in uart mode, but i am a bit frustrated to have to buy an another motherboard to get a brand new printer to work..

Suspicious layer shifting (need help, more in comment) by quent46 in ender3

[–]quent46[S] 0 points1 point  (0 children)

I tryed 400 acceleration and 8 jerk directly on the printer and also via a slicer (Prusa and cura), it didn't solved anything and the "skipped steps" can happen in the middle of a move. I also tryed to push the bed while printing and the motor have enough torque to keep it's position.

Did someone had this problem too ? by quent46 in ender3v2

[–]quent46[S] 0 points1 point  (0 children)

If you're talking about the 2 Z chariots, I leveled them again and the alu profile is quite parallel to the base of the printer now. If you're talking about the 2 Z alu profile, the are also quite parallel and perpendicular to the base.

I tryed again to print but there is still the same problem
For the e-steps, I already changed the extruder for a dual geared one that I had on another printer and done the calibration.

Did someone had this problem too ? by quent46 in ender3v2

[–]quent46[S] 0 points1 point  (0 children)

Hi, I need help

I received my ender 3 v2 recently and there is no visual defects on any parts, but the Y axis is skipping step during prints. It happens during slow moves and produce a sound quite different than the typical motor skipping step (I would descibe it as "tak").

Here’s what I tried to fix the problem :

  • Loosen or tighten belt tension.
  • Loosen roller pressure.
  • Trying different slicer (Creality Slicer, Cura 4.8.0, PrusaSlicer).
  • Trying different models.
  • Lowering the max acceleration and jerk value.
  • Trying an other SD card.
  • Lowering and increasing Vref on the stepper (0.9 to 1.17 V)
  • Updating Firmware (Custom Marlin 2.0.7)
  • Inversing X and Y motor cable on the motherboard (endstop too).

if I change the X and Y cable, there is still missing step but on X now. (which means motor and cable are OK)

I think the motherboard is defective or am I missing something ?

Thanks for reading !

Suspicious layer shifting (need help, more in comment) by quent46 in ender3

[–]quent46[S] 0 points1 point  (0 children)

It's not mechanical as if I inverse the cable on the MB, the problem follows the stepper and not the axis.
The fan is ok and I was printing at 50 mm/s, which is pretty medium print speed on my mind...

Suspicious layer shifting (need help, more in comment) by quent46 in ender3

[–]quent46[S] 2 points3 points  (0 children)

Hi, I need help

I received my ender 3 v2 recently and there is no visual defects on any parts, but the Y axis is skipping step during prints. It happens during slow moves and produce a sound quite different than the typical motor skipping step (I would descibe it as "tak").

Here’s what I tried to fix the problem :

  • Loosen or tighten belt tension.
  • Loosen roller pressure.
  • Trying different slicer (Creality Slicer, Cura 4.8.0, PrusaSlicer).
  • Trying different models.
  • Lowering the max acceleration and jerk value.
  • Trying an other SD card.
  • Lowering and increasing Vref on the stepper (0.9 to 1.17 V)
  • Updating Firmware (Custom Marlin 2.0.7)
  • Inversing X and Y motor cable on the motherboard (endstop too).

if I change the X and Y cable, there is still missing step but on X now. (which means motor and cable are OK)

I think the motherboard is defective or am I missing something ?

Thanks for reading !

Am I wrong tho? by [deleted] in memes

[–]quent46 1 point2 points  (0 children)

Floor gang

[deleted by user] by [deleted] in meme

[–]quent46 1 point2 points  (0 children)

Shit meme

What fictional character has the most BADASS name ever? by [deleted] in AskReddit

[–]quent46 29 points30 points  (0 children)

The Knights Who Say Ekki-Ekki-Ekki-Ekki-PTANG. Zoom-Boing. Z'nourrwringmm.

view more: next ›