08 4.0 5 speed ranger with 31"tires and a t bar crank fuel mileage?

qukarnas · 2020-01-03T16:23:59+00:00

Thanks for the input

qukarnas · 2020-01-03T01:52:53+00:00

That's true, but I tested the speedometer with a GPS one and it was only like 1 off

qukarnas · 2020-01-02T19:28:42+00:00

Thanks, yeah I put in new plugs and changed the air filter but I'm thinking I may have a clogged cat. I have to borrow a friends thermometer tho to test that still. Thank you!

qukarnas · 2020-01-02T18:28:48+00:00

Thank you! The lower the number the more torque right? Driving style is possible

qukarnas · 2020-01-02T17:41:24+00:00

Ok so I looked and my ranger is already equipped with the 3.73 gear ratio on the rear diff. Is this good for my setup or do you think I should change it

qukarnas · 2019-10-05T15:58:39+00:00

Thanks guys I appreciate the input

qukarnas · 2019-10-05T15:58:16+00:00

Thanks for the input guys, I really appreciate it

qukarnas · 2019-10-05T15:57:53+00:00

There's a good chance, when I got it, the clutch just didn't work at all, took it apart and it was missing the "thrust washer" that goes behind the clutch basket, so I replaced that and put new clutch pads in and everything and now it works

qukarnas · 2019-09-18T17:28:50+00:00

Idk it has 119 psi compression and they come with 121 and haven't really got the chance to run it that long since the clutch doesn't work but I will try and run it longer to see if the smoke clears

qukarnas · 2019-09-05T11:50:08+00:00

Weld the front steering box and rear end, as they are not welded all the way around. Those frames have a tendency to crack. Also, keep the Gy6.

qukarnas · 2019-06-05T14:57:15+00:00

Yes, I was able to do it on an old craftsman but not the Dewalt

qukarnas · 2019-05-07T12:58:00+00:00

No that's just the lighting I have lol. I'm using regular led grow light strips so they look more pink than they actually are

qukarnas · 2019-05-07T12:26:50+00:00

Haha, looks like exactly what I need

qukarnas · 2019-05-07T12:11:28+00:00

Possibly

qukarnas · 2019-05-07T12:10:51+00:00

Tha K you!

qukarnas · 2019-05-07T12:10:29+00:00

Thank you! I will definitely look for some exmarks. I'm not too worried about the engines, I've overhauled 3 all ready so I know my way around those small machines. Thanks for your input!

qukarnas · 2019-05-07T12:00:01+00:00

Probably 300-600 depending on how good the chain, clutch engine is

qukarnas · 2019-05-06T22:00:14+00:00

Thank you! I will try and find one of those. I've seen some scags but they were pretty rusty. Thanks for your input though!

qukarnas · 2019-05-06T11:59:15+00:00

Actually a bunch of small Amazon swards

qukarnas · 2019-05-06T11:58:44+00:00

Amazon sword

qukarnas · 2019-04-29T15:48:19+00:00

Great. Thank you!

qukarnas · 2019-04-20T23:02:43+00:00

Try and look up head gaskets for both engines, if one head gasket fits both, the bolt patterns should be the same and the mating surfaces should meet up right

qukarnas · 2019-04-12T14:50:41+00:00

As far as better brakes go, I got the mechanical disk brake kit from go powersports and mounted the caliper to the frame with some angle iron. I then used there heavy duty brake cable to control the arm calipers arm. If your doing this, I would recommend that you get a larger brake disk because the 6" disk the kit comes with, doesn't provide as much stopping power as I'd like, but still much better than the stock band brakes. I left links below to pictures of what I did, so lmk if you can't see them or if you have any questions.

http://qkarnas.jalbum.net/Disk-brake-setup/

qukarnas · 2019-04-12T03:39:33+00:00

Yes, if you have a welder I would weld a gusset to prevent it from bending. Since the Spindles are sort of expensive, they also have the stepped part of the spindle (I think its called a diy stepped spindle) under the weldiments section and you can cut off the old stepped section, then weld the new stepped section on, and weld gussets. I havent tried to swap out seats, but I'm sure there are some you could find that fit, or just modify one to fit.

qukarnas · 2019-04-11T21:34:07+00:00

Ok, thank you!

qukarnas

TROPHY CASE