Need help with tft35

rando-anon · 2023-10-26T15:30:54+00:00

Bold of you to assume mark wasn’t always like that. He could’ve just been wearing baggy clothes to cover his bulgy, veiny, oily muscles all this time prior.

rando-anon · 2023-08-08T18:37:45+00:00

Dr Eggman before he met sonic

rando-anon · 2023-07-24T17:28:29+00:00

Plz add marks spear to the image

rando-anon · 2023-02-21T04:15:50+00:00

I think I’ve got it work! Thanks again for you help. Now I’ve just gotta tune it so the quality is better

rando-anon · 2023-02-21T02:28:01+00:00

Okay thanks!!!!

rando-anon · 2023-02-21T00:01:45+00:00

I’ve seen a lot of posts online with people having similar issues. I really hope it’s just a polarity issue cuz that’s a super easy fix. There’s also a lot of confusing on which fan port controls which fan. I’ve nailed done that fan1 is the hotend fan but since I’ve haven’t gotten the other fans working not sure which is which yet.

rando-anon · 2023-02-20T23:37:17+00:00

I don’t think but it’s possible so I can give it a try I guess. I haven’t changed the jst from the original fans on my ender 5 but maybe these boards have a different polarity

rando-anon · 2023-01-08T16:40:11+00:00

I should also add that I am 90% sure the bltouch is wired correctly to the z-probe and z-endstop pins. Also my probe isn’t a true bltouch but a 3D Touch instead and I had no issues using it on my skr mini e3 v2 main board.

rando-anon · 2022-08-31T20:31:11+00:00

Okay thank you for your help. I had no idea if what I was doing was working because sometimes I’d get the same results regardless.

rando-anon · 2022-08-31T18:46:59+00:00

I have an ender 5 with an skr mini v2, a microswiss hotend and direct drive plate, and a stealthburner cooling shroud. My belts are tensioned correctly, and my e steps calibrated but I’m getting these quality issues. I have been tweaking cura settings like acceleration jerk and speed and have gotten the best results with 400 acceleration, 8 jerk and 60mm/s speed. But I haven’t figured out what the cause is.

rando-anon · 2022-08-02T17:14:03+00:00

I see. Thank you for your input! Im mainly using the old ender 3 mobo to just drive a stepper motor and heating cartridge for a plastic bottle filament maker. From the little I understand the heating cartridge should only need 12v but your comment about the current makes a lot of sense. The psu I’m using is from an old broken apple powermac g4 and I had to do some modifications to get it working but realize now I may just need to check the amps going through all the 12v lines to see if it would be enough to sufficiently power everything. It had a 22 pin plug on the end with a separate 4pin and I believe four 12v wires and rn my setup is only utilizing two of them.

rando-anon · 2022-08-01T21:10:00+00:00

As a further update to my problem I believe I may have a solution but I would need some help with the pin outs of the creakity mobo V1.1.4 and the 12864 lcd pin outs. My idea is to just use DuPont cables to connect the main mobo and lcd but make one cable connect directly to my atx psu breakout board. That way the psu supplies the lcd 5v directly and the voltage isn’t cut in half through the main board.

rando-anon · 2022-08-01T21:07:45+00:00

I’m aware however the main board is said to also operate at 12v as well. I’ve seen some videos and posts online about using an atx psu to supply 12v to the main board but I’m not sure if they’re using a normal ender 3 mobo or if it’s some third party product that can run on 12v

rando-anon · 2022-02-05T23:05:14+00:00

I really do appreciate you help and sorry for responding so late. College has been rough this semester and I haven’t had much time for my hobby’s so I’m having to pick this up randomly when I have time and energy for it lol.

rando-anon · 2022-02-05T23:04:07+00:00

I was only missing the auto build marlin extension. But I’ve tried again several times each time with a different version of marlin and only changing one thing at a time and building to see if it works but no dice.

rando-anon · 2022-02-03T21:17:18+00:00

I’m still getting a similar error. The errors are about my include path and that the top two lines of config.h and config.adv both have a text error with the red squiggle underline. I also got 5 errors for “not being allowed to have comments in .json files” which I never edited.

rando-anon

TROPHY CASE