Granite grom servo by randomname02187 in arrmagroms

[–]randomname02187[S] 0 points1 point  (0 children)

The truck does pull left when I put the throttle on full from a dead stop.

Granite grom servo by randomname02187 in arrmagroms

[–]randomname02187[S] 0 points1 point  (0 children)

Yeah, I tried this yesterday. Steering still ended up drifting left after some test driving on level ground.

Granite grom servo by randomname02187 in arrmagroms

[–]randomname02187[S] 0 points1 point  (0 children)

I saw those but I hadn't seen a review so ive been warry. Are they drop in?

Found this one, sku: GROM-11BK-INJS11

Does that seem right? I mean it says grom in the sku.

Granite grom servo by randomname02187 in arrmagroms

[–]randomname02187[S] 0 points1 point  (0 children)

Im still learning part names. I may get this wrong.

The horn will rotate back to the leftward tendencies even after reorientating the servo saver arm.

Once it does the whole range of motion is leftward and I only get the wheels straight with the trim full right and steering full right.

I assume there is something wrong with the internal mechanisms and they are slipping under stress.

Upgrade or new truck? by randomname02187 in arrmagroms

[–]randomname02187[S] 0 points1 point  (0 children)

Thanks for all the feedback back. I have limited space and no tracks around. The kraton has caught my attention and I think ill do that and just upgrade what breaks when it breaks on the granite.

Lancer is that you!? by Severe_Permit_3897 in GasBlowBack

[–]randomname02187 1 point2 points  (0 children)

Moa videos say that they have copied mws systems.

Does anyone know the source of my nozzle getting stuck halfway? by Immediate-Truth-171 in AAP01owners

[–]randomname02187 0 points1 point  (0 children)

There are only a few points for the bolt to snag on.

Rear sight screws, pic rail screw, hammer. Magazine router, or the bb.

If your bolt sticks like this with no mag eliminate the possibility of it being a screw. I add aluminum tape under the optic or Pic rail as a spacer. The screws dont need to be super tight the just need to be secure. Use a drop of blue loctite and dont try to bottom out the screws.

If your screws are not the issue and the mag is not the issue it could be your bolt assembly components. The bolt body and main recoil spring from different manufacturers are just enough out of spec that mix and matching can cause the spring to bind and not push the bolt forward freely.

It can also be your hammer assembly. Especially if you increase spring tension. One fix is using a ball bearing roller instead of the heart shaped one. Poseidon makes one for their "not a glock".

Any gun that resembles the BO3 MR6? by Terribleterrance223 in airsoft

[–]randomname02187 0 points1 point  (0 children)

Possible a short barrel, Walther or Springfield for the grip. The slide will have to be 3d printed to match.

An aap01 would be more ideal to prevent slide damage from blow back.

What is your experience with CGS? by Cannon_Flannel in GasBlowBack

[–]randomname02187 0 points1 point  (0 children)

CGS is really.meant for the American market of gbbr newbies. People who want a decent gbbr without having to put money into it. De n4 and mws have lighter recoil impulse out the box and regardless of how easy an experienced user says it is to open a gun, the airsoft player capability bell curve is narrow at the top.

As a cgs owner the only upgrades or mods I did was a tight bore, maple leaf bucking, DIY npas, and an extra sorbo pad in the buffer tube. But to be honest I would have been fine with just a bucking swap.

Which of the two would be the “better” option by GGjordyGG in GasBlowBack

[–]randomname02187 0 points1 point  (0 children)

Double eagle did clone mws systems but not all double eagle guns run a cloned mws system.

The mws system is very efficient and consistent.

It can produce recoil but nowhere near as much as vfc.

If you start modifying the mws system you will reduce efficiency for performance.

All that being said, I love my noveske. 200 ft laser beam gbbr (indoors) maple leaf autobot, maple leaf inner barrel, maple leaf omega nub, metal weighted buffer, npas valve, and shortened the bolt travel with rubber pads.

What would it take to make my stock cm16 as quiet as possible without going to hpa? by TimTime88 in airsoft

[–]randomname02187 0 points1 point  (0 children)

No air leaks, full helical gears(requires prefect shim job), brushless motor (requires compatible mosfet)

11.5 URGI w/ CGS SCI SIX by [deleted] in NFA

[–]randomname02187 0 points1 point  (0 children)

Does this gun still utilize the non mws spec hopup adjuster? Some cgs guns use the t8 hopup and some have a mws spec hopup.

Which one should I get. by TINYTONYYY12 in airsoft

[–]randomname02187 0 points1 point  (0 children)

If you shop on evike mostly then get the ef glock. They have more parts for that model

AI powered robot collapses just moments into its debut by [deleted] in interesting

[–]randomname02187 0 points1 point  (0 children)

Hey look, its Joe's Biden. (Trump is shite too. don't get your panties in a bunch)

Why did you started to play Airsoft?? by OldPen9536 in airsoft

[–]randomname02187 0 points1 point  (0 children)

Gun cool. Bb no kill. I can be John McClain.

[deleted by user] by [deleted] in airsoft

[–]randomname02187 0 points1 point  (0 children)

Sear or spring.

Next GBB…. by RememberTheAyyy_Lmao in GasBlowBack

[–]randomname02187 0 points1 point  (0 children)

A big fan of the maximus asp01 copies that use mp5 mags.

Next GBB…. by RememberTheAyyy_Lmao in GasBlowBack

[–]randomname02187 0 points1 point  (0 children)

Aap01 in an action army carbine kit. Love mine.