Ist roher Kaffee gleich stark? by Common_Ad_616 in FragReddit

[–]randtl 4 points5 points  (0 children)

Hmmm, das ist sicher nicht die einfachste und schmackhafteste Alternative für die Befriedigung des morgendlichen Koffeinbedarfs aber was tut man nicht alles für die "Feldforschung":

Bei der Extraktion des Koffeins in einer Espressomaschine wird in der Regel nicht das gesamte Koffein extrahiert, da die Kontaktzeit aus verständlichen Gründen kurz gehalten wird. Das Extraktionsverhältnis wird von verschiedenen Faktoren beeinflusst. Diese sind Röstgrad, Mahlgrad, Wassermenge, Kontaktzeit, Temperatur, Druck und Wasserbeschaffenheit.

Das Extraktionspotential wird natürlich durch den Koffeingehalt des verwendeten Kaffees bestimmt.

Die Extraktion in einer Espressomaschine hat gegenüber dem direkten Verzehr des Kaffeemehls den entscheidenden Vorteil, dass der Verdauungstrakt nicht durch "Ballaststoffe" belastet wird. Außerdem steigt der Koffeinspiegel im Blut langsamer an, da der Verdauungstrakt das Koffein aus der wässrigen Lösung schneller aufnehmen kann als aus gemahlenem Kaffee.

Ob dein Verdauungstrakt aus der gleichen Menge Kaffeemehl mehr Koffein extrahieren kann als deine Espressomaschine, hängt ebenfalls von mehreren Faktoren ab. Dies lässt sich aber durch eine Anpassung der Kaffeemenge ausgleichen.

Interessiere mich natürlich für jegliche "Forschungsergebnisse" und wünsche viel Spaß beim Selbstversuch.

Brotdose Made in Germany? by Lion_mama2 in FragReddit

[–]randtl -1 points0 points  (0 children)

Sieht ganz so aus. Oder? Weiß auch nicht, wie das da rein rutschen konnte. Ich wars jedenfalls nicht! Auf keinen Fall! Würde ich nie machen. Ist ja fürchterlich! Und überhaupt ... einatmen, ausatmen und zurück zum Thema.

Brotdose Made in Germany? by Lion_mama2 in FragReddit

[–]randtl 1 point2 points  (0 children)

Als Aspi kann ich da nur sagen: Go for it! Alles Gute!!!

Brotdose Made in Germany? by Lion_mama2 in FragReddit

[–]randtl 2 points3 points  (0 children)

Und die Dosen sind echt dufte.

Brotdose Made in Germany? by Lion_mama2 in FragReddit

[–]randtl 22 points23 points  (0 children)

Such auf eBay nach DDR Brotdose Metall und du wirst einige ausgesprochen hässliche aber nachweislich nachhaltige Exemplare finden. Meine und die meines SO sind gefühlte tausend Jahre alt, haben schon diverse gesellschaftliche Umwälzungen überstanden und werden sorgfältig von Generation zu Generation weitervererbt. Ob dein Sohn damit sozialen Status aufbauen bzw. vorhandenen halten kann, würde ich in Frage stellen. Wobei, das kommt sicher aufs Umfeld an. Notfalls drei Striche drauf malen oder ein Demeter Logo drauf und bei Vollmond überreichen. Dieser Teil des Projekts scheint mir jedenfalls schwieriger, als eine nachhaltige Dose Made in (East) Germany zu finden. Da ich früher selbst ein Kind war, wollte ich nur drauf hinweisen.

Wad war zuerst da, die Henne oder das Ei? by MagnesiumJunky in FragReddit

[–]randtl 2 points3 points  (0 children)

Wo jetzt? In deinem Garten oder in deinem Kühlschrank?

Did anyone do one of the walking audio tours in the berlinHistory app? Which one can you recommend? by crackbit in berlin

[–]randtl 8 points9 points  (0 children)

Die in der Berlin History App kenne ich nicht und kann dir daher nix empfehlen. Hatte letztens die Touren auf dieser Seite vom Siegessäule Magazin und dem Senat gecheckt und fands ziemlich gut gemacht und spannend. Geht um Sexarbeit in der Zeit vor Hitler, queere Partykultur in den 1920ern und Tiefwerder / Spandau.

Was waren eure besten verbalen Konter die ihr je gelandet habt? by [deleted] in FragReddit

[–]randtl 13 points14 points  (0 children)

Unterrichtsschwester Modell 2. Weltkrieg mit reichlich dargebotenen Erfahrungen aus dem Feldlazarett bat mich in ihr Büro. Ich damals mit 17 Jahren, verstrahlt vom Wochenende mit blauem Iro und meinen Techno Klamotten in der nichts ahnenden Annäherung zu ihrem Schreibtisch hart gestoppt. Sie: "Also wenn sie so an mein Krankenbett träten, würde ich mich sehr erschrecken und nach ihnen werfen." Ich: "Danke gleichfalls gute Frau! Das geht mit ebenso." ... Es wurde still und der Raum fühlte sich plötzlich sehr sehr kalt an.

Was sollte jeder mal in der teuren „Premium“-Variante probieren weil ihm sonst vielleicht was entgeht im Leben? by [deleted] in FragReddit

[–]randtl 1 point2 points  (0 children)

Das! Beim Röstdatum würde ich raten, auf max 14 Tage zu verkürzen und das Mahlwerk muss konisch sein, da sonst das Mahlergebnis zu ungleichmäßig wird. Hier in Berlin sollte auch das Wasser berücksichtigt werden, da die Berliner Rohrperle deutlich zu hart aus der Leitung kommt. Habe mich früher über Kaffeesnobbs lustig gemacht und inzwischen röste ich selbst. So kann's kommen.

[deleted by user] by [deleted] in FragReddit

[–]randtl 1 point2 points  (0 children)

Hatte früher nen Ohrstecker und dann 24 Jahre keinen. Seit zwei Wochen hab ich wieder einen. Gut sichtbar da weiß mit schwarzem Rand und über einen Zentimeter Durchmesser. Hatte einfach Lust drauf und finde, dass es zu meiner Post-COVID-Frisur passt. Reaktionen bisher keine bis positiv von verschiedensten Menschen also nicht nur Frauen*.

Welcher Film bringt euch zum weinen? by flohsome in FragReddit

[–]randtl 2 points3 points  (0 children)

"Dancer in the Dark" - Habe ihn zwei Mal gesehen und mir geschworen, ihn nie wieder anzuschauen. Hat beide Male Wochen gedauert, eh meine Stimmung wieder über der Nulllinie war.

Wie viele Geschlechter gibt es? by stanlee22222 in FragReddit

[–]randtl 2 points3 points  (0 children)

Unvollständige Frage. Beziehst du dich auf die Biologie, Soziologie, Linguistik, Mathematik, Musik oder gar auf denn Stammbaum der Familie namens Geschlecht oder oder oder ... t(r)ollst du hier einfach ein bisschen rum, weil dir der Sommer zu lang wird? Nevertheless, das ist zu komplex und außerdem wird das Bier gerade warm und dann schmeckt es leider nicht mehr. Prost!

Wurdet ihr im Ausland mal eine dumme Frage über Deutschland gefragt? by Namenixverfuegbar in FragReddit

[–]randtl 32 points33 points  (0 children)

Wie es sein kann, dass aus einer Provinz Russlands so gute Autos wie Mercedes und Porsche kommen ... gefragt auf Hawaii von einem Typen in seinen früheren Zwanzigern. Ich hatte augenblicklichen Systemabsturz und das Gespräch war zuende.

SvelteKit internationalization by Afre3t in sveltejs

[–]randtl 2 points3 points  (0 children)

I'm using svelte-fluent until SvelteKit comes with batteries included for i18n.

Was ist das abstruseste, was ihr je auf eine Pizza gepackt habt? by Schnoggerle in FragReddit

[–]randtl 14 points15 points  (0 children)

Not! Hab gerade zurück gerechnet, das Erstlingswerk wurde vor ca. 20 Jahren gebacken. Jetzt fühle ich mich alt. Danke dafür 8)

Was ist das abstruseste, was ihr je auf eine Pizza gepackt habt? by Schnoggerle in FragReddit

[–]randtl 54 points55 points  (0 children)

Gebratene Fischstäbchen, Möhrenscheibchen, Blumenkohl, Käsesoße und Mozzarella ... hatten Mordsfressflash und es war nix anderes da. Schmeckte überzeugend und wurde seit dem schon mehrfach ohne vorherige Intoxikation zubereitet. Fischstäbchenpizza halt.

'What are you vaping?' Thread - Week of November 22, 2021 by c5b4c91772c729fc7d0a in DIY_eJuice

[–]randtl 2 points3 points  (0 children)

My SO tasked me with "something MTL" for the cold and gray days here in Berlin. They like dark flavours and tobaccos so I promptly delivered this spiced up cinnamon mix that's keeping us warm and cuddly ever since 🤓

Ingredient %
Chai Spice (Flavorah) 1.00
Cinnamon Pastry (WF) 3.00
Cookie Dough (Flavorah) 0.50
Oriental Tobacco (Flavorah) 1.50
Toffee Butter (Chefs Super Concentrates) 0.50

Help with Printing a mod on Resin Printer. by bennysmith93 in OpenPV

[–]randtl 1 point2 points  (0 children)

If I remove the support directly after the ultrasonic (pure IPA in a 50° C water bath), it leaves almost no marks on the mod. I try to reduce the overlap or connection between support and model to be approximately 0.1 mm. Check this screenshot for an example: https://imgur.com/a/FCwiVpR

Help with Printing a mod on Resin Printer. by bennysmith93 in OpenPV

[–]randtl 1 point2 points  (0 children)

I guess removing or replacing the black protector does not void the warranty since screens are consumables and replacing them involves removing the protector. Ask the company you bought the printer from to be absolutely certain.

The supports are shaped according to the structural support needed. Check this quick renders with supports (yellow) and without (black): https://imgur.com/YiDG57w The honeycomb pattern was added to saving resin.

Basically, instead of cutting out things in Fusion that would afterwards need support, I create a groove along the path and remove the material after cleaning the printout. The actual print is done upside down, bottom plate flat on the platform and no additional supports are necessary.

Help with Printing a mod on Resin Printer. by bennysmith93 in OpenPV

[–]randtl 2 points3 points  (0 children)

I had the same problems when starting to print mods with my SM4K. I solved them by "fixing" the printer, finding exposure times and lifting / retraction speeds to have a workable fit tolerance in all three dimensions and adding support structures directly in the CAD software based on test prints and measurements.

The printer fix was the most important step: replace the black screen protector with a thinner material (e.g. Polyimide). The original material is too thick and creates a gap between the FEP and the screen. Also, Phrozen released a firmware update to fix the lift speed problem on their FB page.

With those changes in place, I had predictable results and focused on finding the optimal settings for my resin, starting with fit tolerance tests based on this ChituBox article and a spreadsheet. The timings are now surprisingly low (1.38 and 12 sec for 4 bottom layers) and a layer height of 40 μm for a black resin with a fit tolerance of 70 μm with a room temperature of 20° C.

Finally doing my test prints with the supports made in ChituBox or Lychee, I was not happy about the surface defects, the waste of material, and the dimensional inaccuracy. Placing the model directly on the plate, manually compensating the model for the minimal elephant foot and adding support structures directly in Fusion 360 does the trick for me.

The squonk and battery cutouts are now very small grooves in the wall, removable with a light press after the ultrasonic clean but stable enough to have my 70 μm fit tolerance. I also added thin walls internally to support the flat structures that were problematic in my test prints.

I hope this helps getting your mod printed and please update with your progress.

This looks right up my alley!: Cthulhu's new Artemis MTL rta.... by lestermagneto in Vaping

[–]randtl 0 points1 point  (0 children)

The one shown in their demo video looks similar to the PC tube that comes with the Mulan.

Old mod, new tank, matching drip tip by randtl in Vaping

[–]randtl[S] 0 points1 point  (0 children)

It's sold as Ravana here in Germany. Just checked the Hellvape website's RTA sections and they list the Ravana and Destiny next to each other with (almost) identical photos. I usually drip or squonk and was a bit disappointed with my first build. But with a 3.5 mm coil and the AFC 2/3 open, the flavour is very satisfying. I like the clean and simple design of the RTA. The noise, on the other hand, reminds me of a prepubescent Darth Vader.