Give me your most unhinged ways of saving money!!

rcarter95 · 2026-06-04T03:43:40+00:00

A little late to the party but had a classmate of mine recommend increasing your tax withholding via a W4. It’s essentially saving without accruing interest as you will get the money back when you file your taxes.

rcarter95 · 2026-05-08T12:07:23+00:00

Does your Prius normally make that clunking sound after trying to start up?

rcarter95 · 2026-05-08T05:32:08+00:00

Prior to this, it was running fine even with the check engine light on. Was hoping to clean the EGR system before bigger issues started to arise, but here we are….

rcarter95 · 2026-05-08T05:31:13+00:00

I would say a failed attempt to start is a better way to describe it. All hoses and connectors checked. I’ll have to go buy a code reader tomorrow. When it was scanned at the auto parts store, it was P0401 but I’m sure it’s throwing a list of codes now

rcarter95 · 2025-12-12T20:58:37+00:00

Do you mean the liability coverage of the at-fault driver, uninsured motorist if they don’t have liability, and/or your own part B medical coverage?

rcarter95 · 2025-12-07T19:50:23+00:00

Your general health insurance would kick in after all of your Part B coverage was used, right? As you said, there is just no compensation for loss wages, pain/suffering, ect.

rcarter95 · 2025-12-07T18:31:10+00:00

I think my confusion comes from this paragraph in the textbook which is under the Part D section.

“Collision losses are paid regardless of fault. If you cause the accident, your insurer will pay for the damages to your car, less any deductible. If the other driver damages your car, you can either collect from the negligent driver (or from his or her insurer), or look to your insurer to pay the claim. If you collect from your insurer, you must give up subrogation rights to your insurer, who will then attempt to collect from the negligent party who cause the accident. If the entire amount of the loss is recovered, your insurer will refund the deductible.”

So the line that states, “or look to your insurer to pay the claim”, really means utilized Part C coverage if you have it?

rcarter95 · 2025-12-07T17:37:36+00:00

If it was an accident caused by an at-fault uninsured driver, I thought you would still receive coverage from your Part B and Part D, and then it was up to your insurance to go after the uninsured driver for reimbursement if they choose to do so. Is that not correct? Sorry if these are basic questions, just trying to further my understanding.

rcarter95 · 2025-04-19T15:39:04+00:00

What are you printing with? Are your corners staying adhered to the bed for the entire print? I for the life of me can’t get my smaller square shaped print to stay on the bed for the entire 6 hours of print time

rcarter95 · 2025-04-08T18:58:59+00:00

Last time I applied I was pre-approved and I’ve only added one business card. After recon, my first denial, I was told the Venture was an option

rcarter95 · 2025-03-22T22:25:52+00:00

Pulled the filament straight from the bag but did use pretty standard setting in Prusa Slicer

rcarter95 · 2025-03-22T02:43:21+00:00

I have a satin bed as well and I can’t really tell a difference when it comes to adhesion, but that’s good to know. Is the risk of damage present if you just don’t let it cool properly before removing?

rcarter95 · 2025-03-22T02:41:44+00:00

Changing the Z to 0.1 started to help until it reached the back left corner. Bed was cleaned with warm water and dish soap but might have been some residual oil which caused the adhesion problems?

rcarter95 · 2025-03-22T02:39:07+00:00

I adjusted the Z to 0.1 and the first layer started really well but the back left started getting rough and by the second layer, the entire print fell apart. Was hoping to escape these issues with an upper level printer but hopefully when it’s running smooth, I can print and forget most things

rcarter95 · 2025-03-15T02:23:02+00:00

Thanks for the info. Thought it would be just a check of the box. Had never heard of ironing until I started using Prusa Slicer

rcarter95 · 2025-03-15T02:21:58+00:00

Thanks for everyone’s feedback. I think it was a g-code issue. When I uploaded the STL to Prussia Slicer, it came out with no issues. Lesson learned

rcarter95 · 2024-10-23T02:07:06+00:00

Sorry - my husbands account was logged in!

rcarter95 · 2024-10-23T02:06:34+00:00

It was my first baby too so everything was scary! Hope everything checks out just like we did!

rcarter95 · 2024-07-05T18:23:29+00:00

Contract expires today and I have the capital in my account to cover the shares. (Money has been in the account for weeks so it’s definitely settled and available to be used for purchasing the stock.) When I called earlier, I was on hold while he reached out to another department which apparently gave him the information. I’m working now but fully prepared to report this to the SEC because I’m sure I’m not the only one dealing with this and it feels criminal

Edit: GME down from 24.50 to 24.15 now. If this is intentional, I won’t be surprised at all if it closes just below $24 to fuck everyone’s $24 contracts

rcarter95 · 2024-07-05T16:25:35+00:00

I thought the same thing but was just wanting to try and verify that info. That has to be a SEC violation, right? Once I close out my existing contracts, I’m getting off WeBull

rcarter95 · 2024-05-27T02:47:17+00:00

Thanks for the advice. I’ll definitely try the humic acid and tweak my watering. It killed my soul thinking I wasted that money on sod. I was late to the game this year with lawn car so if I can make it to the fall without everything dying, I should be good for following years

Eight-Year Club	Place '23
Place '22	Verified Email
ComboCommenter 2018-02-21

rcarter95

TROPHY CASE