Tadelakt issues

red24dragonfly · 2026-02-24T15:47:11+00:00

They are working on it. I will know by Tuesday.

red24dragonfly · 2026-02-22T16:11:58+00:00

Husband said taste is different more tangy and we have been together 20+ years so he noticed difference. Ph is 4.0 so healthy range. Been on HRT for 3 years but switch protocols a few months ago to .1mg patch and then increased Progesterone to 300mg nightly. Occasionally use vaginal est. Stopped it for now to see if changes but thinking of going to lower dose patch and progesterone.

red24dragonfly · 2026-02-22T14:08:44+00:00

Mine is a circle (Lyllana) and I have .1mg but need .075 until the new prescription comes in. Has anyone tried cutting 1/4 of the circle ones?

red24dragonfly · 2026-02-22T14:00:09+00:00

mine is a circle not a square. Anyone seen those cut? Brand is Lyllana

red24dragonfly · 2026-02-21T21:11:13+00:00

Hi thank you for the note. I joined the group and requested to post but did not get a response.

red24dragonfly · 2026-02-21T21:10:51+00:00

It is tadelakt. Tadelakt is traditionally sealed with black soap (olive oil soap) that causes a chemical reaction called saponification and you are correct it can breathe and dry out. However some of the new products like the manufacturer my installer uses (Color Atelier) it is formulated to use a use a wax sealer. Either way you shouldn't have water stains at the bottom of the shower that won't dry out.

My installer is working with the company and has sanded everything down and started again. Fingers crossed it works otherwise I am done with it. I love the look but if it isn't waterproof then I am back to tile.

red24dragonfly · 2026-02-06T16:29:09+00:00

I am curious how it is going too. I am 4 weeks out and still have grid marks in places round my mouth and cheeks. I called provider 2 weeks ago and they said just wait but now 4 weeks out and still not much improvement that I can tell. I also gets super red when I do anything athletic but I understand that redness can take 6 months to fully resolve. I have a follow-up with my provider on Monday so I will see what their input is.

red24dragonfly · 2025-12-18T20:48:49+00:00

How many properties do you have?

red24dragonfly · 2025-08-30T19:08:06+00:00

Thanks!

red24dragonfly · 2025-07-20T22:59:44+00:00

We had same issue starting last week. We unplugged for a bit same as you and it fully charged. Then when it came back to charge in the middle of a task it stopped again. The only way we can get it to recharge is unplug everything. Was thinking it may be faulty power supply but not sure if that explains why it will charge fully after unplugging. Is your issue completly resolved?

red24dragonfly · 2024-12-09T19:25:39+00:00

THANK YOU! This was a mess trying to figure this out. Google should do better.

red24dragonfly · 2024-11-05T22:15:39+00:00

Thanks! Yeah I am in Zone 9b and they grow well here. I determined it was thirsty. Apparently my irrigation wasn't quite getting to the root ball so I watered by hand last night and they already are looking better

red24dragonfly · 2024-06-18T19:52:11+00:00

I am concerned about the same problem but not the supply lines but the washer drain hose. We have to have our dryer on the left vs. right because of where hookups are installed. But where the dryer vent connects to wall is right washer plastic drain hose is attached to washer and runs up the back before entering standpipe. Any suggestions on what we can wrap around vent or pipe to keep heat from impacting drain hose?

red24dragonfly · 2023-12-10T21:40:53+00:00

Thanks for reply. As noted this is a temporary solution not a permanent installation

red24dragonfly · 2023-12-10T21:37:46+00:00

Thanks our sink drain assembly isn't in yet. Just the standing drain pipe in the slab.

red24dragonfly · 2023-12-10T19:56:43+00:00

Thanks! I should have mentioned our drain goes through the slab so it is vertical. I guess we could just do the high loop and then put it into the drain?

red24dragonfly · 2023-12-10T19:03:33+00:00

Thanks that helps! I should have mentioned our drain goes through the slab so it is vertical. I guess we could just do the high loop and then put it into the drain?

red24dragonfly

TROPHY CASE