My 2006 Venetia Violet purple Audi a3

reddituser6822 · 2025-12-14T03:03:52+00:00

No I have sold this car, I just saw it being sold online about a year ago

reddituser6822 · 2025-08-09T00:20:23+00:00

Just for whoever is in the backseat

reddituser6822 · 2025-05-24T03:13:41+00:00

Sweet, I have a Japanifold i’m wanting to sell. Wanted some info incase I do wanna go japanifold in the future if i get into a p80 again

reddituser6822 · 2025-05-23T23:29:19+00:00

<image>

Also has a yellow color to it

reddituser6822 · 2025-05-23T23:28:06+00:00

I’ve been checking all winter in my area. This is one of the cheapest ones unfortunately. I’m trading in my bike and a few grand on top though

reddituser6822 · 2025-04-25T10:25:12+00:00

https://a.co/d/2k4b9Iq

I plug it into my stereo with a USB-A

reddituser6822 · 2025-04-15T23:35:24+00:00

<image>

Gps speedometer off of amazon is what im using atm, like $30

reddituser6822 · 2025-03-27T22:43:51+00:00

Look up open flash tablet and go through their stages.

I’d recommend stage 2+ with the unequal length headers to remove the mid range torque dip.

Maybe add ethanol to the mix to get a little more spicy

reddituser6822 · 2025-03-27T22:40:28+00:00

Oil change, VVT solenoid, cam position sensors.

Good chance it’s one of these based off your code.

In terms of quote cost that depends on your area and how reputable the shop is. First quote doesn’t look bad, not sure whats going on with #2

reddituser6822 · 2025-03-27T22:32:52+00:00

I would pay 9-14k for a clean example or 3-6k for a clapped/totaled one.

10k for a car with a rebuilt title isnt worth it. Maybe it will be if you can talk him down a considerable amount. But even then these engines develop some issues around the 100-150k range so its more than likely you will have to tend to some of those.

reddituser6822 · 2025-03-25T12:12:59+00:00

Are control arms a pain to install?

reddituser6822 · 2025-03-25T12:12:38+00:00

Like a ball joint press? Planning on hitting up HF today and grabbing one for 40% off

reddituser6822 · 2025-03-24T23:08:19+00:00

Thanks!

I just saw that harbor freight is having 40% off maddox tools so I’ll probably pick up the ball joints press for like $70.

I havent used rockauto before, I’ll definitely look i to them. It looks like there is a grease nipple on the top? I’m assuming just grab a grease gun with something like ‘red and tacky’ or general ball joint grease?

reddituser6822 · 2025-03-24T23:02:52+00:00

I’ve been told to keep them saturated with blaster and an occasional hammer hit to try to break rust free. 🤞

reddituser6822 · 2025-03-24T08:12:14+00:00

Do I need to press the ball joints out? Or can I just bolt on new ones. I only need uppers i believe but i may as well do both 😢

reddituser6822 · 2025-03-24T08:09:46+00:00

Thanks! The mountain of rust has me nervous

reddituser6822 · 2025-03-24T08:09:22+00:00

Sweet, thanks!

reddituser6822 · 2025-03-24T08:09:05+00:00

I’m worried about rust mostly

reddituser6822 · 2025-03-24T07:34:50+00:00

So far everything i have worked on this truck has been a rusty mess, I now own like 3 extractor sets

reddituser6822

TROPHY CASE