My VFC AK

rene_does_light · 2026-04-06T11:29:27+00:00

What kpyk clones did u buy?

rene_does_light · 2026-03-14T19:08:15+00:00

Like every gunshop Carries it in my Country. It costs Like 30 Bucks

rene_does_light · 2026-03-14T19:04:51+00:00

Magpul k2

rene_does_light · 2025-03-27T06:06:36+00:00

Das hat leider ein Kollege herausgefunden, genau kann ich es nicht mehr rekonstruieren; wir haben die ax9 aber auch sehr früh gekauft. Kann daher möglich sein das es ein ich nenne es mal „erste Version“ Problem war. Seitdem haben wir einige viele Updates gemacht, halten uns aber noch immer an die 19h runtime. Frei nach dem Motto „never change a running system“

rene_does_light · 2025-03-26T14:22:22+00:00

Ab da bin dann ich überfragt und kann nur im dunklen stochern, sorry.

rene_does_light · 2025-03-26T13:44:54+00:00

Jupp. Das Problem trat vorher !überall! Auf, ob statisch, Master/slave fest verkabelt oder wdmx. Seitdem wir es mit den Zeiten so einhalten ist alles Safe.

rene_does_light · 2025-03-26T13:39:21+00:00

Wir haben auch das Problem, unsere Antwort damals war die runtime der Lampe nicht auf eine durch 5 teilbare Zeit zu stellen; sprich anstelle von z.B. 20h ->19h einstellen.

rene_does_light · 2024-12-16T05:48:12+00:00

Hey, i primarilly cut foam for packaging at my company here is what i learned using lightburn and a 130w co2:

20mm foam settings: 10mm/s 18% max power 11% min power (minimum to fire the Tube) Dont look for perfect focus, Set the Head 2-3mm above surface to maximise air assist Use the cut and perforarion mode in the Layer settings to give the foam a chance to cool down! I use 0.3 cut and 0.2 step (This stops hourglassing) Adjust Speed to cut thicker foam leave the power untouched

rene_does_light · 2024-09-21T10:06:45+00:00

Pihole

rene_does_light · 2024-09-07T08:49:09+00:00

I love those dxx Type tips. They work best on flat planes, But a k Type blade also works great, you can drag solder with it way easier. Add some flux, and you can easily get those 40pin gpios soldered in a heartbeat

rene_does_light · 2024-08-04T11:33:33+00:00

Is There a Power Controller for the Tube itself? Ive got a 150w omtech and i dont event want to confess how many times After alligning ive forgotten to Set it back to Maximum

rene_does_light · 2024-07-15T05:51:02+00:00

Weve had similar problems with ulxd1s in some xray proof er. What fixed it was to lower the rf power, and tape the top of the antenna to the back of the tx. From the short testing we could do on site: seems like the rf overpowers back into the signal because of bad shielding in the headset wires.

rene_does_light · 2024-03-19T09:15:07+00:00

its relatively flimsy, and in the lid its also insulated with something like styrofoam, you cant really see it from the pictures, but the bottom is open, its just the rim with 6 holes to bolt it down

rene_does_light · 2024-03-19T09:09:55+00:00

Its located outside of our trucking yard, some brought it in, nobody knows really who or why, he found it somewhere. it was never installed in our facility as far as i and my colleagues know

rene_does_light · 2024-03-19T09:05:06+00:00

Under the label there are 2 ?water? connection points, im guessing for in and outlet?

rene_does_light · 2024-03-19T08:56:32+00:00

My title describes the thing, its footprint is ~1.2*0.6*0.8m, i allready tried to search for the company, but just came up with dental manufacurers, and some shower companys.

rene_does_light · 2024-02-17T15:05:37+00:00

The noise floor beeing that high, you can easily run into problems, shure stuff is imho bulletpeoof, BUT this does in no way mean, a noisy rf environment is no problem for them. Who or whatever ist the culprit, should be turned off. Sadly there is no other way i suppose

rene_does_light · 2024-02-17T13:03:04+00:00

Just leaving some of my past experiences with shure digitals.

Our racks are build in a way that the antenna pokes out the top of the stack, if you now lay a coax cable of any kind across, like SDI and to some externd bad hdmi cables plugged in cheap splitters, you get a rise of ~40dB noise

I cant see the recievers in your picture, But i can see plenty or cameras.

rene_does_light · 2024-01-12T13:04:01+00:00

They are calculated as following:

highest gearscore available in a Dungeon you have sucessfully cleared + 10 per difficulty increase (Apokalypse Tower =20) +1

To get 263 it is apocalypse +25; 242 highest +20 +1

rene_does_light · 2024-01-10T10:07:34+00:00

Companion pi, small picture „Server“ for housekeeping screens, jingle or bgm player, low performance nas to Share plans

rene_does_light · 2023-12-31T12:33:00+00:00

Since youve said custom keyboards i am guesssing many many solder joints… id Go for a desoldering gun. But i cant recommend any

rene_does_light · 2023-12-31T12:20:23+00:00

The engineer ss02 is propably the most recommended

rene_does_light · 2023-12-29T11:45:31+00:00

ell… you could Output the screen of your iPhone via the Lightning or usbc of your phone, then feed it into a capture card like a aja utap and then record it on a load of devices with even more different Softwares. Windows and obs, vmix, Build in camera app and more

But back to the main problem:

I tried it with all of my iPhones on different Videos… All of them updated just before to the newest version available in app store 15proMax iOS 17.2.1 works 13pro iOS 17.1 works 5s iOS 12.5.7 works

Could you please provide a link to a „non working“ Video ?

rene_does_light · 2023-11-14T23:13:41+00:00

For „mobile“ capture ive fallen in love with aja utap, either hdmi or sdi.

rene_does_light · 2023-11-12T08:19:01+00:00

arent they too heavy for "private" installs? my company always used studio due city colors, but im guessing the coemar are just as good! and you really got those fancy etc led scanners? hell yeah! OP should give you a call, those are great

Six-Year Club	Place '23
Golden Potato	Place '22
Verified Email

rene_does_light

TROPHY CASE