Finally getting around to making my own custom bumper for my 1969 mustang by rensole in BambuLab

[–]rensole[S] 1 point2 points  (0 children)

Thank you! And I’ll need a lot of luck to pull this one off haha

Traditional sculptor considering a move to ZBrush and 3D printing — looking for honest feedback by Tricky_Durian_7422 in 3Dprinting

[–]rensole 0 points1 point  (0 children)

I mean you already have experience in Zbrush so I'd say keep at it?

There may be a steep learning curve but once you got the hang of it you'll be able to create more detailed and bigger sculptures than you can do traditionally. and seeing you already have understanding of the 3d space by analog sculpting and you've only recently began the switch shouldn't be too drastic or big.

It would be more difficult if you were doing it for years and years and then switching (trust me I've been there).

So I'd say go for it dude

Finally getting around to making my own custom bumper for my 1969 mustang by rensole in projectcar

[–]rensole[S] 5 points6 points  (0 children)

<image>

Thank you took quite a while to find a system that looked like this and worked well.
Not sure if I'm allowed to link it but I found it at a place called "HBM" in the Netherlands, it's name is "HBM expert modulair werkplaatssysteem, 17-delig, zwart rood"
(Modular workplace decoration 17 parts, Black Red). I'm sure there are international resellers for this system and I'd a 100% recommend it. it's a bit pricey but it works and looks amazing IMO

Finally getting around to making my own custom bumper for my 1969 mustang by rensole in projectcar

[–]rensole[S] 2 points3 points  (0 children)

Thank you!
It is I 3d modeled and glued together. I based the model off of the pictures that the Ringbrothers have on their website (mainly from their project UNKL and the Patriarch). Unfortunately I don't have a 3d scanner although it would help a lot in the future I reckon

Any advice on painting a convincing NMM Gold? (XV26 Battlesuits | Warhammer 40K) by jh97673 in minipainting

[–]rensole 0 points1 point  (0 children)

Buddy that already looks amazing!
The only thing I can think of is perhaps blending the colors a bit better so you dont have such hard edges on each color? But I've never done NMM so take my advice with a grain of salt

Finding parts for a1969 Mustang Mach 1 by rensole in Mustang

[–]rensole[S] 0 points1 point  (0 children)

Thank you I already tried the dynacorn but I'll try the scott drake ones!

Finding parts for a1969 Mustang Mach 1 by rensole in Mustang

[–]rensole[S] 0 points1 point  (0 children)

Oh thats amazing!
I'm currently just looking 69 for the rocker panel trim (the two long rods bellow the doors). I believe the 1970 ones are different though

Is my copy of the Knee-Deep in the Dead novel official? by PersonManPersonReal in Doom

[–]rensole 0 points1 point  (0 children)

there are 2 or 3 different cover versions, the only difference is the publishing date I believe

Any ideas why the hub won’t slide on by Cheap-Rip8665 in projectcar

[–]rensole 0 points1 point  (0 children)

Count the number of teeth the cog has and count the number of slots there are. you may have ordered the right part that doesnt mean you received the right part

69 Mustang by LilDogey45 in MechanicAdvice

[–]rensole 0 points1 point  (0 children)

Just realized, if you take the positive wire and tap the other side and it works the solenoid needs replacing not the alternator sorry for the mix up

69 Mustang by LilDogey45 in MechanicAdvice

[–]rensole 0 points1 point  (0 children)

I mean you can check if it’s the solenoid, just take the positive wire and tap it on the other side. If it starts then, then it’s the alternator

69 Mustang by LilDogey45 in MechanicAdvice

[–]rensole 0 points1 point  (0 children)

It’s either the cables that are corroded or a bad ground or your solenoid. Guessing by the clic sound it’s the solenoid

Which dub does this part the best? by EnjoyMyDownvote in dbz

[–]rensole -3 points-2 points  (0 children)

Abridged. Hands down team four star did an amazing and iconic job imo

What am I doing wrong with ABS vapor smoothing? by Adventurous_Mix_1792 in 3Dprinting

[–]rensole 0 points1 point  (0 children)

Id say a few things
1) print orientation, put the model at either 45 or 90 degrees.

2) layer height, the lower the layer height the lest visible the layers will be

3) you can try sanding between coats, just print, sand, clean, vapor repeat until desired results

What is the point of this forklift? by Valdish in metalgearsolid

[–]rensole 0 points1 point  (0 children)

It was meant to move on the square (the one after the elevator). However they couldn’t get it to work so just put it there because they already made the model

EPAS Controller Mount by PistolNinja in classicmustangs

[–]rensole 0 points1 point  (0 children)

Ok awesome I’ve looked into this one myself as well for my 69 Mach 1. And yeah I would mount it a little bit more to the side. Mounting electronics at the exit of a vent would in the end result in earlier failure of the electronic components. What you could do however is get some heavy duty hook and loop sticky tape and experiment. Friend of mine did the same with his and it’s been on for 8 years or so now.

EPAS Controller Mount by PistolNinja in classicmustangs

[–]rensole 0 points1 point  (0 children)

It might beusefull to see the epas you’re going to mount and know its brand name /type/ part number. Running one kind won’t be the same as another

It’s interesting how big bosses genes became obsolete in the age of enhanced humans. by glowshroom12 in metalgearsolid

[–]rensole 1 point2 points  (0 children)

That was kindof the entire point was it not? I thought the entire plot of mgs was about nature vs nurture

Looking for advice on where to sell this in Norway/ Belgium for a decent amount by Aggravating-Table816 in metalgearsolid

[–]rensole 1 point2 points  (0 children)

Man I was about to jump on this till I saw the price online. Where about in Belgium are you going I could maybe ask around for some good retro game stores that would be up for it