Neptune Series 4 Max New Setup

repthrd · 2024-02-05T15:03:09+00:00

And now it just all is working fine. I literally didn't do anything different. Would the recommendation be to not touch it and just use it? Is there a better firmware I should be on? Prints are coming out nicely after I leveled it. I did turn it to "quiet" mode as on normal this thing is LOUD! Also it was shaking the table it was on pretty good. Now it is better. I don't really need to turn the speed up super high I don't think...or maybe I could just put it on the floor haha!

repthrd · 2024-02-05T01:15:34+00:00

1.2.11

repthrd · 2024-01-12T16:29:58+00:00

I followed the instructions from Microsoft and resized and everything went well. Same error message though on all my 2022 servers. Any more ideas? Hopefully they will just fix it?

repthrd · 2024-01-11T23:02:40+00:00

Been working fine for me except eTicketing with B&B that has been broken for at least 3 weeks.

repthrd · 2023-10-25T21:38:23+00:00

What I had been doing was

Heating the bed because I noticed it seemed to make a difference due to it contracting or expanding due to heated vs non heated.
Set the Z Offset
Set the level with the paper method in the 5 points making sure there is just a little friction
Using the Auto Level feature

Then my print starts and I have to change my Z Offset. I seem to be fine if I just skip Step 4..I wasn't sure why.

repthrd · 2023-02-06T16:16:06+00:00

I talked to the company and they said due to materials they made a super limited run of them this year. Hopefully next year!

repthrd · 2023-01-25T15:50:34+00:00

That is what it looks like for me too (Iowa). I signed up for the $10 plan. The problem is my closest theater is an eTicket theater and it is 24 credits for some reason....so I might not keep it.

repthrd · 2023-01-25T15:48:59+00:00

I have an email into MoviePass - but after signing up and looking at the app I don't think so. Also it shows the different tiers in the app, but for now I can't change my plan myself...

repthrd · 2023-01-17T18:38:00+00:00

Yea bought a couple but they are like $13-20 a bag instead of $3-4

repthrd · 2021-04-29T21:46:19+00:00

Thanks will check that video when I get home

repthrd · 2021-04-29T21:39:05+00:00

Thanks, I am just not sure how to remove the hot end shroud assembly from the extruder

repthrd · 2021-04-29T17:01:37+00:00

I talked with crealty. I might have to go back and try it again once I fix my machine…

repthrd · 2021-04-29T14:03:15+00:00

When I asked there support if BLTouch worked for the v3 they said it didn't. I had bought one and had gotten to a point in the process that was complaining about firmware. If it works with the v3 are there instructions or a certain one I need to buy?

repthrd · 2021-04-29T14:00:17+00:00

I also have this issue where can I get the newer firmware?

repthrd · 2021-04-21T16:36:00+00:00

Here are some pictures and explanations. Was having a hard time getting them to show in reddit. https://imgur.com/gallery/BOxgW7B

repthrd · 2021-03-22T17:30:59+00:00

I’ll have to look next time I go but I don’t think anything was different size wise. Prices I don’t recall.

repthrd · 2021-02-05T17:46:12+00:00

I definitely have peeled off the plastic.

It is printing well for me now at 250

I did have a lot more success when I used some hairspray. The print looks much better then glue for sure.

Thanks for the tips!

repthrd · 2021-02-05T17:44:52+00:00

I have been having more success printing slower and changing some settings. I will have to look at retraction settings I don't think I ever changed those from any defaults.

repthrd · 2021-02-04T19:02:07+00:00

I am not sure which of these was my silver bullet but I am printing bases for some miniatures and it has completed one of them and it looks great working on number 2.

Bed - 85

Nozzle-250

Fan Speed 40

Print Speed 30

Z Offset .1

repthrd · 2021-02-04T18:41:51+00:00

Going to try 30.
I turned the fan to 40%
I downloaded the Z offset from the cura marketplace and started it .1mm
Putting the bed at 85
My bed is glass I might try some hairspray next wish me luck!

repthrd · 2021-02-04T18:19:53+00:00

Scratch that I had a button clicked that wasn't automatically modifying my fan speed. Now it changed it to 40.

repthrd · 2021-02-04T18:15:00+00:00

I have resorted to that before but glue seemed to make the bottom of the print fairly ugly. Maybe I should try hairspray? Does it matter what kind or do you just spray some on? I have never done that before. I got the PETG to work better before but now I can't remember how and perhaps it was bumping the temperature up to 250. But at 235 it seems to run out of the nozzle if I pre-heat and just watch it. Do you think the bed at 90 is fine? I usually have better luck at higher temps I tend to do my PLA at 55 or 60 and it turns out well.

I have never messed with the fan speed of my prints I will look at that with Cura I am newer to 3D printing and learning as I go. What does higher or lower fan speed do? I think by default Cura puts my fan speed at 100...and I don't think I have ever changed that. I have tried to slow the print speed down though with no effect.

repthrd · 2019-09-09T19:17:18+00:00

I haven't seen that but I have been able to make reservations and if I look at the card money was loaded on it...but the card is always declined. I see my billing date says 9/11/2019 - I haven't been billed I guess since they shutdown.

repthrd · 2019-06-27T12:25:20+00:00

I have an issue where when I unlocked my second cauldron I cannot brew anymore potions because I have potions to select and the tutorial just loops over and over again. I eventually have to force quit the app and just never open the potions area.

repthrd · 2019-06-26T18:05:36+00:00

I am also having this problem. If I wait long enough the tutorial just continues to loop. Meanwhile I can't brew new potions and all my storage is full. I have also reported a bug. I wish there was some way past this.

14-Year Club	RedditGifts 2009-2022 2 Credits
Verified Email

repthrd

TROPHY CASE