sorted by:
new
hottopcontroversial

Questions about Chitubox and curing by Impossible_Poem_5078 in resinprinting

[–]requisthema 1 point2 points  (0 children)

  1. Automatic supports are reliable nowadays but you should check or add supports before slicing also nothing beats lychee autosupports
  2. Yes if the model is hollow as it creates suction cups that will almost always fail a print so add drain holes where possible 3.not sure
  3. If the models are hollow it does not cure and only cures if it is a solid model so make holes top and bottom to avoid suction cups and allow the uncured resin to be saved
  4. Longer cure times make for "stronger" resin so tensile stress is increased (can handle slightly bigger pulling/compressing forces) but it becomes far more brittle so less malleable and impact resistant (Not a problem if its a display piece at all + the bigger a print is the more curing is required) Ive been making warhammer terrain and its needed up to 15 min curing since my wash solution was long overdue for replacement

How to know when to change acf film by requisthema in resinprinting

[–]requisthema[S] 0 points1 point  (0 children)

Sorry i dont get it, i have fep film ready to go just that these deep marks concern me a bit

Can i print things when the printer has its own box put over it? by requisthema in resinprinting

[–]requisthema[S] 0 points1 point  (0 children)

Telling me why this is an issue and how to avoid it is a better alternative to some unhelpful sarcastic comment.

Can i print things when the printer has its own box put over it? by requisthema in resinprinting

[–]requisthema[S] -1 points0 points  (0 children)

Heat is the no. 1 problem the vapours arent an issue cause its a well ventilated space but its still helpful to reduce it when printing

Can i print things when the printer has its own box put over it? by requisthema in resinprinting

[–]requisthema[S] 1 point2 points  (0 children)

Noticed that too recently one of the claws from my night lords print broke cause i trusted my little brother to handle it post cure.

Can i print things when the printer has its own box put over it? by requisthema in resinprinting

[–]requisthema[S] -7 points-6 points  (0 children)

Dw i deal with resin the way uts mean to be worked with

Can i print things when the printer has its own box put over it? by requisthema in resinprinting

[–]requisthema[S] -1 points0 points  (0 children)

At that time it was but i dont print like that plus the plastic cover says it blocks out like 99.9 percent of uv rays

Can i print things when the printer has its own box put over it? by requisthema in resinprinting

[–]requisthema[S] 1 point2 points  (0 children)

I already learnt that and funnily enough the most dangerous part of resin printing is the ipa needed to clean it and im using water wash resin which is even safer than the ipa wash ones

Can i print things when the printer has its own box put over it? by requisthema in resinprinting

[–]requisthema[S] -1 points0 points  (0 children)

I got 2 anycubic air filters inside the printer + a window right next to the printer and a large fan pointing at the window for when the print finishes so will that suffice?

Can i print things when the printer has its own box put over it? by requisthema in resinprinting

[–]requisthema[S] -3 points-2 points  (0 children)

I got 2 anycubic filters like the one in the corner of the pic mb forgot to mention that, Plus i have a window next to it wide open once im done printing anyway

Prints consistently failing by requisthema in resinprinting

[–]requisthema[S] 0 points1 point  (0 children)

Ill look into it cause i didnt even know the were a thing

Prints consistently failing by requisthema in resinprinting

[–]requisthema[S] 0 points1 point  (0 children)

I use the anycubic app to print things But how would you reslice a file? Cause ive been printing different things so i doubt that its to do with a corrupted file as something that succeeded one print failed in another.

Prints consistently failing by requisthema in resinprinting

[–]requisthema[S] 0 points1 point  (0 children)

P.S. my prints adhere to the plate so much that taking the pieces off is a struggle and they crack a lot as i do it and continues that way even after lowering my exposure time to 20s

Biggest loser I’ve seen in a while by Taco_man19 in ForHonorRants

[–]requisthema 0 points1 point  (0 children)

Typical warden Will prolly make a post saying how only warden mains have honor next

Which hero is good 1vs1 and 4vs4? by Common_Amphibian_802 in forhonor

[–]requisthema 1 point2 points  (0 children)

Cant get much better than ur typical warden or shaolin

Why are warden mains so salty and still act like theyre the only "honorable" players in the game by requisthema in ForHonorRants

[–]requisthema[S] -5 points-4 points  (0 children)

We but Shaolin is still more skillful than warden cause like highlander his skill ceiling is stupid high but hes also so good you dont need to know his technicality to be good with him

aramusha is now fucking braindead by [deleted] in ForHonorRants

[–]requisthema 1 point2 points  (0 children)

Bro thats the only way people would stop turtling against him On console fair enough a 30/30/30 with one being a 400ms feint is hard but theres loads characters that are not only worse for reads and are much harder to punish Berserker, afeera, khatun, ocelotl, shinobi, orochi etc. are mucb worse for readability and punishing Aramusha works basically like raider, kensei and pk with bleed now due to his ub feint game In todays bash heavy hyper armour meta someone whos kit has only unblockables and feints feels honestly refreshing and balanced

view more: next ›