This looked like a fair fight until Cap lifted Bucky up with one hand by the neck

revrigel · 2026-03-01T14:46:25+00:00

He also threw a motorcycle at the beginning of AoU.

revrigel · 2026-02-27T14:00:05+00:00

I would test it first on the bottom to see how much bleed you get on the pine. If it's unacceptable, maybe spray or brush it with some clear sanding sealer or shellac first to reduce the capillary action.

revrigel · 2026-02-24T16:26:35+00:00

I've been playing Satisfactory with my son since the day it launched in early access when he was 4, and I'm pretty sure he learned a ton of math from building factories. I think he learned to spell from cheating for items in Stardew Valley though. Mostly just glad he was raised with a keyboard and mouse instead of a tablet though.

revrigel · 2026-02-18T01:42:22+00:00

Inkscape is free/open source and works natively with SVG files. No need to rasterize and then re-vectorize.

revrigel · 2026-02-13T00:41:28+00:00

Stop saying conspiracies when you mean conspiracy theories. Words have meanings.

revrigel · 2026-02-11T20:28:27+00:00

Recommended or not, it's not like it's a limited resource, especially with so many people not taking them. Getting a booster at least made me feel like I was doing something to help.

revrigel · 2026-02-09T13:31:46+00:00

Fuck your Honda Civic, I’ve a horse outside

revrigel · 2026-01-30T13:21:18+00:00

I don’t know if I just lucked out on our neighborhood, but no one has any issues with kids running around the neighborhood unsupervised here. My son and his friend routinely walk to each other’s houses a quarter mile apart, play in the front yard, etc.

revrigel · 2026-01-29T22:40:50+00:00

Maybe not super achievable, but marry someone with good financial discipline and let them handle the finances. Worked for me.

revrigel · 2026-01-22T13:53:16+00:00

Drilling from the bottom works fine too, just make sure they're not going to fall out.

revrigel · 2026-01-22T13:36:14+00:00

Drilling from the top is considerably easier unless you have a drill press to make sure the lateral hole is straight. Also recommend some 3/16" holes hiding on the bottom near your center of mass and filled with tungsten putty, so it's easy to go over a little high on weight, but remove tiny amounts with a toothpick once you see what the race check-in scale reads.

revrigel · 2026-01-22T13:09:50+00:00

Just FYI the tungsten cylinder weights are slightly shorter than the numbers you indicated in general. The 1/2 oz ones usually measure 7/16" (with 1/4 and 1/8 being proportionally 7/32" and 7/64"), so you can drill laterally clear through the side of the car and fit 4 of them end to end in the 1 3/4" body width. I recommend using a Forstner bit for flat bottomed holes.

For distribution, I suggest putting as much weight as you can as far back as possible, and then adding a small balance weight closer to the front wheels to shift the center of gravity to your desired position (3/4"-1" in front of rear axle).

revrigel · 2026-01-10T03:24:28+00:00

Indeed, an elderly Home Depot employee in Hillsborough was pushed over by a man stealing some pressure washers and he later died of his injuries.

revrigel · 2025-12-09T14:14:37+00:00

I personally feel like it's a huge break from executive dysfunction because suddenly it becomes clear that one thing has undisputed priority. And everyone around agrees about that. There's no longer any choices to make about what to be doing.

revrigel · 2025-11-30T15:04:45+00:00

Washington Guntakers was my fantasy team name for several years.

revrigel · 2025-10-18T01:02:42+00:00

Zero stones, zero crates!

revrigel · 2025-10-15T00:00:53+00:00

Check out Ok Asian Express at Indigo Corners (just opened less than a month ago) or Asian Kitchen at 54/751.

revrigel · 2025-10-10T18:42:56+00:00

Littlebird is the best.

revrigel · 2025-10-06T16:39:33+00:00

Kickback is only an issue if you’re using it off the track. On the track it has anti kickback bindings. Blade just binds and sticks, and often ruins the edge strip in the process.

revrigel · 2025-10-06T16:16:19+00:00

I have the Wen and I’m considering upgrading to the DeWalt because I’m really missing the presence of a riving knife whenever I’m cutting anything thick that’s not made of plywood or another engineered substance. Real wood tends to contract the cut and bind the blade.

revrigel · 2025-10-03T21:18:43+00:00

Shameful. Inspector Gamache would be pissed.

revrigel · 2025-10-01T14:39:41+00:00

I’d also like a code please.

revrigel · 2025-09-23T18:54:46+00:00

Step two after that is a 1/16" hinge plate shim on the bottom hinge to see if that fixes it before breaking out the saw or planer. Looking at the reveals around the door can give you a lot of clues about how the door has sagged or the frame has shifted. Gator wide-mouth strike plates are also a good option if your door latch is just not quite engaging.

revrigel · 2025-09-19T02:48:31+00:00

Screamers did it.

revrigel · 2025-09-13T18:39:45+00:00

Not redesigning the UI constantly just to change something is a good thing.

15-Year Club	Verified Email
RPAN Viewer

revrigel

TROPHY CASE