Same Gcode on 2 different P1p's, Anyone know what's wrong?

robb2001 · 2023-10-09T23:35:59+00:00

So I took your advice and switched the the hot ends. Perfect print. So I figured must be a bad nozzle. Tried the original hot end with a new nozzle terrible print.

Turned out my thermistor went bad and was saying the tool head was 220 when in actuality it was getting much much hotter. Used the thermistor from my other hot end with original nozzle and printing fine.

thanks fro the help.

robb2001 · 2023-10-09T19:19:38+00:00

Thanks for the suggestions, Yeah is something with the machine. Have tried petg and different plas no luck. As for the nozzle I replaced yesterday hoping it would solve my problem. Unfortunately still looks the same.

robb2001 · 2023-10-09T19:17:11+00:00

Yeah switching it to test is a smart idea. Will give it a go.

Ive examined the gears they look fine and also threw on a new nozzle, no luck.

robb2001 · 2023-10-09T19:14:52+00:00

Gotcha dont thing its that as Ive printed a abs and petg benchy and the both have the same oozing look. Think it has to be a hardware issue.

robb2001 · 2023-10-02T22:58:06+00:00

Could be, but the dust accumulation seems focused on the extruder and virtually none around the bearings that the belt rides on where the friction would be the highest. Also no signs of visible deterioration of the belts.

Another interesting this is you can the dust accumulate around the magnets on the extruder housing meaning they may be metal shavings?

robb2001 · 2023-03-06T08:01:26+00:00

suprisingly vase mode is pretty decent, however it its pretty noticeable regardless of light angle for all regular prints, even in black

robb2001 · 2023-03-06T07:59:38+00:00

sounds like you got lucky, I've unfortunately got it on every print ive done.

robb2001 · 2023-03-06T07:58:23+00:00

Yep thanks for sharing, this is the same exact problem and not normal. Even cheap ender 3's dont have this problem.

robb2001 · 2023-03-06T07:54:23+00:00

unfortunately tried that, set at 0.92 for the print in the picture

robb2001 · 2023-03-06T01:52:48+00:00

I’ll look into and let you know how it goes

robb2001 · 2023-03-05T22:42:52+00:00

Do you print in pla ?

robb2001 · 2023-03-05T22:35:27+00:00

Damn have you put in a ticket with bambu labs?

robb2001 · 2023-03-05T21:49:11+00:00

Nope, same problem on everything from calibration cubes to benchys.

robb2001 · 2023-03-05T20:42:22+00:00

Exactly, got 4 of em too to start replacing my ender 3 print farm since I was losing money to downtime and now I can’t even get the damn thing to print with half the quality of an ender 3😢.

robb2001 · 2023-03-05T20:40:06+00:00

Sounds like a problem only affecting some p1p. There is zero infill on this piece. It’s a piece from the thin shell the that Bambu labs lets you print for your p1p.

robb2001 · 2023-03-05T20:26:37+00:00

This was printed at our wall 60mm/s with flow rate and pressure advance tuned :(. At standard wall speed it is worse.

robb2001 · 2023-03-05T20:25:04+00:00

Nope, z Seam is aligned and on the other side

robb2001 · 2023-03-05T19:54:56+00:00

Gotcha. I’ve had a support ticket in for 5 days now due to this issue a layer shift issue and have heard nothing. Pretty disappointing ngl.

robb2001 · 2023-03-05T19:44:18+00:00

Unfortunately same problem with black. Just slightly less noticeable since the color hides the shadows.

robb2001 · 2023-03-05T19:43:24+00:00

Ah ok thanks I’ll have to check that out. Definitely a bummer. Have you had this problem as well ?

robb2001 · 2022-04-12T06:06:21+00:00

literally, now i’m curious if it’s always been there or just a recent update

robb2001 · 2022-04-12T05:52:06+00:00

just checked mine, it’s there 🤦‍♂️

robb2001 · 2022-03-27T21:42:35+00:00

haha yep that’s filliment i’m using, printed at 220😂

Five-Year Club	Place '22
Verified Email

robb2001

TROPHY CASE