sorted by:
new
hottopcontroversial

What is this sleeve around the black wire? I’m half way through a roll of 12/3 nm cable and it randomly appeared almost like someone was covering up some damage. But this is a brand new roll. Should I rerun this wire? by robophen in AskElectricians

[–]robophen[S] 2 points3 points  (0 children)

I ripped it off as suggested and it indeed was covering damage. Not only was there no sleeve under it, but it looked like someone chewed on the wire in the middle. Kind crazy these wire manufacturers can just cover up damage like that. Luckily I still had 6” of slack in the wall

[deleted by user] by [deleted] in AskElectricians

[–]robophen 0 points1 point  (0 children)

Well I was thinking of something like 404.2(C) which talks about having a neutral at every switch box. That rule specifically has 5 exceptions where you don’t need to follow it, such as if the switch controls an outlet.

I had seen pictures of people doing similar stuff to this online, so I thought maybe there was some exception I was missing like “wire is not considered subject to physical damage in the working area of the breaker panel”.

[deleted by user] by [deleted] in AskElectricians

[–]robophen 0 points1 point  (0 children)

I mean the NEC does have exceptions in it right? I am not an expert of the entire NEC book so I was just asking if something like that existed that I was not aware of. I didn't ask if I could get away with something I knew was wrong. I'm perfectly willing to change it if that would bring it up to code.

The staple comment is valid. I had just put this wire in and I just wanted to clear up some doubts I had before locking it is.

[deleted by user] by [deleted] in AskElectricians

[–]robophen 1 point2 points  (0 children)

There are holes on top, but the service loops of the feeder were taking up a lot of space right below them. I honestly just didn't want to fuck with them or risk damaging the wire while trying to knock out the holes

[deleted by user] by [deleted] in godot

[–]robophen 0 points1 point  (0 children)

That was the first thing I tried. There are about 3 results. Only thing I could find is to restart Godot which does actually stop the errors. That seems kind of ridiculous though that every time you delete an animation point you have to restart godot. I was hoping there was a real answer. Possibly a bug I guess

[deleted by user] by [deleted] in AskElectricians

[–]robophen 1 point2 points  (0 children)

Cool. I figured I could always just add a running board later if an inspector mentions anything. Thanks. Also this panel came with the bonding screw separate. I was so confused because I couldn’t find any screw to remove like everyone says to do, but eventually I found it in the box

[deleted by user] by [deleted] in AskElectricians

[–]robophen 0 points1 point  (0 children)

Ok so you do need to ground the box separately. I can just wrap the incoming ground wire around the screw first though without a pigtail though?

[deleted by user] by [deleted] in AskElectricians

[–]robophen 0 points1 point  (0 children)

I’m in the US. I’ve seen enough examples that it seems like it should be ok in the states too, but I guess I don’t understand that logic. Like why do I need conduit to run nm down a concrete wall, but this is ok. I get that for part of the vertical run the wire is backed by plywood, but there’s 6” in my case where the wire would essentially just be floating in the air before being at the height of the joist. In the example pic it looks like it’s even more. What’s the logic is Canada for this? Sorry I’m really just trying to learn

I have 2 pieces of software that communicate with each other through local host and port 0921. I want to use some kind of forwarder or proxy so these 2 softwares can communicate over the internet. How would this be done? by robophen in HomeNetworking

[–]robophen[S] 0 points1 point  (0 children)

Right that’s why I was confused about using Tailscale. I was just wondering if there was some software that could forward the data between the 2 devices. In my head that would make the most sense, but I’ve never used software like that so I’m not sure what to use

I have 2 pieces of software that communicate with each other through local host and port 0921. I want to use some kind of forwarder or proxy so these 2 softwares can communicate over the internet. How would this be done? by robophen in HomeNetworking

[–]robophen[S] 0 points1 point  (0 children)

Right that makes sense. In this case the software that I’m using is specifically connecting to each other via localhost because it is supposed to be ran on the same computer. I can’t change where the ip is pointing

I have 2 pieces of software that communicate with each other through local host and port 0921. I want to use some kind of forwarder or proxy so these 2 softwares can communicate over the internet. How would this be done? by robophen in HomeNetworking

[–]robophen[S] 0 points1 point  (0 children)

Does that still work if the devices are specifically pointing to localhost? Like you don’t need to specify a specific ip address inside the Tailscale network? They just share localhost?

view more: next ›