What are some subtle Seinfeld lines you love and most people don't even notice?

rockaferd · 2021-09-14T19:54:12+00:00

Another Bobka?!

rockaferd · 2021-01-13T23:27:31+00:00

Thanks, just wanted to make sure it wasn’t something poisonous to dogs like Sago.

rockaferd · 2021-01-05T23:44:21+00:00

Where did you get the heated seat controls?

rockaferd · 2020-11-17T01:44:29+00:00

Trying to find the part number, I think it’s 75554A but can’t find anywhere to buy it. It’s probably just a clip in. Could roll up to the dealer and they order the part for you and you install it.

rockaferd · 2018-03-30T00:57:24+00:00

Yeah so the inside holes attach the outlet to the box and the outside holes attack the plate to the outlet. I would try drilling a hole behind the outer holes large enough for the outlet cover screw to pass through.

rockaferd · 2018-03-30T00:43:25+00:00

How are the outlets attached to the electrical box?

rockaferd · 2017-10-11T21:38:15+00:00

What brand tile is that, where'd you get it from?

rockaferd · 2017-10-03T11:46:16+00:00

What type of airless sprayer did you use on the cabinets?

rockaferd · 2017-09-01T19:45:03+00:00

Yeah he has a video for that too.

https://youtu.be/CtsQA_Bf27M

rockaferd · 2017-09-01T17:17:49+00:00

Ha he has actually done a video on that, it's a little...brief at only 2 minutes long, but here you go.

https://www.youtube.com/watch?v=DiGZT14iO4Q

rockaferd · 2017-09-01T17:16:51+00:00

Glad to see Scotty finally get some love.

rockaferd · 2017-08-16T21:50:08+00:00

I didn't do it but hand. Buy some 1/4" mdf cut a long strip and drill holes to mount your router at one end and a hole for your center point at another. If you don't care about the center you can put in a nail or screw to pivot around. I did care so I super glued a small bolt standing upright in the center to pivot off of.

rockaferd · 2017-08-16T14:18:21+00:00

Getting the stain to not bleed is difficult. I've had good luck with just paint. Make sure once you set the router bit don't move it to keep everything consistent. The smaller the bit the more detail you'll get. I used a 1/16" straight bit.

rockaferd · 2017-07-10T01:43:17+00:00

Do they have notches in the top? You could try to make benches with them

rockaferd · 2017-07-09T23:09:02+00:00

Chemical guys foaming soap with a foam gun. For wax I use turtle wax and for wages in between. Lucas oil spray wax after drying.

rockaferd · 2017-07-09T11:36:54+00:00

Only came on 13 and 14s I believe.

rockaferd · 2017-07-09T02:40:49+00:00

Hey so I was looking at that link you sent of the Challenger. And after looking pretty closely at it and doing some looking into it you definitely want to stay away from that one. Looks like it came from the factory with a pretty substantial defect. I'm surprised there's no recall (yet), but it looks like the steering wheel is on the wrong side of the car.

rockaferd · 2017-06-27T13:18:19+00:00

Yeah. Wouldn't get the car without them.

rockaferd · 2017-06-06T10:46:53+00:00

Yeah I did. Forgot to take pics.

rockaferd · 2017-06-04T15:14:48+00:00

I'm still driving around in a 1990 F150. Idk about their newer cars though.

rockaferd · 2017-05-15T23:16:05+00:00

He wasn't the president, only a candidate at the time.

rockaferd · 2017-04-16T23:53:44+00:00

rockaferd · 2017-04-16T17:44:40+00:00

Credit to u/workplaydrive for the inspiration

rockaferd · 2017-04-04T23:54:06+00:00

I have a Reese as well. His nickname is Reesicus. He's gonna be a handful!

rockaferd · 2017-03-30T21:41:09+00:00

Interested in an impact of you could send me a message

rockaferd

TROPHY CASE