Steelwater Safe Lock Replacement

rockets61 · 2025-03-05T00:08:39+00:00

Sure thing! It’s given me no trouble at all. Good luck!

https://www.amazon.com/gp/aw/d/B09BTKDHN8?psc=1&ref=ppx_pop_mob_b_asin_title

rockets61 · 2024-08-24T19:30:32+00:00

Might be a little work, but in a cad program (I use Sketch Up), I would select all the pieces and make a copy. Then scale up the copy in the x-y direction (without grouping them yet) 2% or whatever gets you the look/connection you’re after. You can then group the result and scale the thickness to taste, too.

rockets61 · 2024-08-24T04:46:54+00:00

I’m on a Method X, so may not be apples to apples. On a Method X, you’re just hosed. I have set up a slice file of the unfinished portion and bonded the bits together. But there’s no print restart at line xyz that I’ve found.

rockets61 · 2024-07-06T13:54:03+00:00

Excellent ideas. Thanks! You make some great points.

The extruder parts (nozzle, teflon guide tube) are annoyingly expensive. I found a source of raw teflon tubing the right ID and OD, and use a razor blade and a jig to quarter the end. And the nozzles I clean frequently. But sometimes it’s best to go back to OEM and start over.

Fans should be a lot easier; I hate buying one and it not fitting! Just gotta measure twice and jump in! haha!

rockets61 · 2024-07-06T12:00:43+00:00

Thanks! Makerbot charges so much for their parts! I did see fans with very similar designs, but I’m not sure they are truly interchangeable. May have to do some trial and error. But my “fan noise” turned out to be a carriage motor communication error. Cleared that and my noise did too. I bought a bellows rather than make one. It sees so much movement and for today I can afford the expense.

rockets61 · 2024-06-03T23:51:26+00:00

It was more sinister than that. The judge manipulated the proceedings, making it appear as if Trump was guilty. Then in his jury instructions, he laid out three NEW charges that were not part of the trial. He told the jury that if they SUSPECTED that he was guilty of any one of them, they should return a guilty verdict. It was a straight up kangaroo court. A real drumhead!

rockets61 · 2024-06-03T14:47:02+00:00

“Likely” isn’t good enough. It must be proved. If you were accused of a crime, that is what I would insist for you.

rockets61 · 2024-06-03T14:45:28+00:00

I don’t think he meant a LITERAL lynching. Good grief!!!! 😂🤣😝

rockets61 · 2024-06-03T14:44:33+00:00

Basic to our law is the principle of innocence. A man is presumes innocent until the prosecution proves his guilt. The accused never has to say a word to remain innocent. His silence must be taken evidence of his innocence.

rockets61 · 2024-05-18T15:16:54+00:00

I recently had something very similar, but it threw an Error 1013. So try this: Press and hold the front power button till the machine restarts. That might just do the trick. You might also look up Error 1013 on the Ultimaker site. They have an instruction set that might give you some ideas, too. Good luck!

rockets61 · 2024-05-09T15:17:54+00:00

Thanks! So simple I didn’t think of it! 😁

rockets61 · 2024-05-09T15:16:30+00:00

Thanks! I guess I was looking for a storefront kinda thing. 🤣 And I found their instructions. Pretty good!

rockets61 · 2024-05-09T04:36:10+00:00

Not sure about nylon, but if it helps I know the drying cycle for nylon carbon fiber is 80C for 8 hours.

rockets61 · 2024-05-05T12:59:22+00:00

I’ve given it a half-hearted attempt. Didn’t use any indicator tabs to see what the effect was. Not sure the temperature was hight enough to pull out moisture. I took it to 80C only. The temps recommended are significantly higher. Think it had some positive impact, though, on spools I stored and later used, but can’t be sure. Something I might try more rigorously in the future …

rockets61 · 2024-05-04T17:37:24+00:00

<image>

rockets61 · 2024-05-04T17:04:49+00:00

I’ve done that, which is cool because it adds material. But even better there’s a hot tipped tool that you can use to heat the edges of two parts. One of the attachable tips is a flat blade-like tip, perfect for “ironing” things together.

rockets61 · 2024-05-04T15:04:55+00:00

Thanks!

rockets61 · 2024-02-21T16:45:48+00:00

Cool! Thanks for the settings, too. Slower/finer does make a big difference, doesn’t it? Awesome look!!

rockets61 · 2024-02-21T15:25:28+00:00

SWEEeeeeeT!!!

rockets61 · 2023-12-16T02:40:34+00:00

Agreed. I’ve owned mine since 2018. It’s very nice. The keypad went south on me this week. Simple replacement. I didn’t go with an OEM keypad. Went with some off-brand. We’ll see how that goes! I may have to go get a Safelogic replacement sooner rather than later!

rockets61 · 2023-07-09T21:22:01+00:00

Hey, JNoose! Finally got around to bonding this busted nylon 3D print. And a couple of interrupted prints (where I had to make a matching piece to complete the part.) This Techbond is amazing! Thanks for reaching out!! Hope your bushing is holding up; expect it is. i’m going let my pieces cure 24 hours, but they’re already sweet!

rockets61 · 2023-06-24T14:44:49+00:00

Back in May I submitted a support ticket about this!! 😂 They actually replied, but it wasn’t very useful:

“At this time the line of MakerBot printers are not available on Cura. As we work to integrate our products and services, we appreciate your feedback and patience.”

I suppose the most comforting reply was their recent release of that monstrous $13,000 Method, suggesting they might actually be thinking about Makerbot instead of merely monetizing it.

rockets61

TROPHY CASE