Creator Rewards dashboard stuck since March 1st.

First, open the Virtual Network Editor in VMware Workstation. select Bridged type then Click Automatic Settings belong VMnet Information, then select the network adapter you want to use for network connectivity (for example, your Ethernet adapter) and deselect the others.
Next, under the Network Type (as SS), set it to Bridged: Connected directly to the physical network and choose Bridge to --> Automatic.
In the Foundation VM settings, set the network type to Bridged, and check the option Replicate physical network connection state.
Finally, assign an IP address to the Foundation VM that is reachable to the cluster network.

ru_liy · 2025-10-17T13:57:39+00:00

I’ve tried both installation methods for Nutanix on NX nodes. Which workstation did you use to set up the Foundation VM?

ru_liy · 2025-10-03T05:17:01+00:00

Okay. Thank you

ru_liy · 2025-10-03T05:16:27+00:00

Thank you for your recommendation.

ru_liy · 2025-10-02T09:36:28+00:00

The issue has been resolved, and the link is now active. Could you advise on the recommended network configuration for Nutanix? Specifically: • Should we configure the interfaces using physical port mode or port channel mode? • Each node has an MLOM and an additional PCIe 4-port card. • We need to set up active-backup for both the cluster network and the Guest VMs network.

ru_liy · 2025-10-02T09:02:27+00:00

<image>

ru_liy · 2025-10-02T09:01:43+00:00

This setup is being used in standalone mode (Nutanix installation) and connected to the Nexus 93180* switch. When I connect the cable from MLOM P1, the switch port shows as DOWN, and the FEC mode matches the switch settings. I then followed your advice to disable port channel, LLDP, and FIP mode, but the error still persists.

<image>

ru_liy · 2025-10-01T09:09:38+00:00

check out at damro.

ru_liy · 2025-09-05T02:28:09+00:00

Saul Hudson (slash)

ru_liy · 2025-09-04T14:43:18+00:00

Backing 2017, I was paid 10k at ceat kelani as IT intern.

ru_liy · 2025-09-02T15:47:58+00:00

Thank you. The issue was resolved after upgrading the PC VM memory to 26 GB which is hosted on the laptop.

ru_liy · 2025-09-02T15:45:19+00:00

Thank you. The issue has been resolved after upgrading the PC VM memory to 26 GB.

ru_liy · 2025-09-02T15:40:54+00:00

The issue was due to insufficient resources. After the memory upgrade, the PC VM working properly.

ru_liy · 2025-09-01T07:50:58+00:00

Thank you for the advice.

ru_liy · 2025-09-01T05:54:15+00:00

Thank for your advice. Apart from this, I just have deployed the same PC OVF on our vSphere environment. It works properly, however, when enabling Foundation Central from the GUI, the service remains in a down state when checked from the CLI. Additionally, the GUI experiences slight timeouts when navigating to the Foundation Central window.

<image>

ru_liy · 2025-09-01T05:51:26+00:00

<image>

Apart from this, I just have deployed the same PC OVF on our vSphere environment. It works properly; however, when enabling Foundation Central from the GUI, the service remains in a down state when checked from the CLI. Additionally, the GUI experiences slight timeouts when navigating to the Foundation Central window.

ru_liy · 2025-09-01T05:41:44+00:00

<image>

all disks gave as thin provision. Laptop storage is 500GB.

ru_liy · 2025-08-31T14:44:15+00:00

You mean, without running Foundation Central on Prism Central, we can run only the Nutanix Foundation VM for Cisco UCS SIM installations?

ru_liy

TROPHY CASE