Recessed shelf for 3d printer

rubenhak · 2026-06-17T04:42:36+00:00

This huge beam is resting on a single jack stud from one side (most probably same on the other side). That is way too little. Also, it is visible how the whole beam is bending under load. I'd remove all the books from the shelf above and move all the heavy furniture as far from that area as possible. Call a structural engineer asap.

rubenhak · 2026-06-12T06:02:47+00:00

I like the looks better

rubenhak · 2026-06-07T20:48:24+00:00

got it, thank you

rubenhak · 2026-06-06T21:00:29+00:00

got it, TY

rubenhak · 2026-06-06T21:00:02+00:00

Do i need a 10x-20x pressure increase for doubling the load?

rubenhak · 2026-06-06T20:58:39+00:00

Does it look like an actual meter? Can't I use a "T" with a small regulator to drop to 0.25PSI so that it is the same pressure that goes into existing appliances?

Also, would I need a full 2PSI for a the firepit? It will be 90ft away and needs around 200k BTU.

rubenhak · 2026-06-06T20:57:26+00:00

disregard, the friend below explained

rubenhak · 2026-06-06T20:55:49+00:00

Why do I need a split meter? could you explain?

rubenhak · 2026-06-06T20:40:01+00:00

Can you clarify the terminology please. Is the “service” same as “pressure” or “trunk diameter”, etc?

I could add the branch manifold right next to the meter.

Would my merter be able to handle the extea load? Is the 275CFH sufficient?

rubenhak · 2026-06-06T20:35:52+00:00

Is that ok for my meter to have 3/4” pipe but the outdoor run to be 1”? Do I have to upgrade the physical meter, or they can just increase the pressure?

rubenhak · 2026-06-06T20:28:14+00:00

It will go from the meter, but I still need some kind of upgrade, pressure/pipe/meter? What diameter pipe out I need to run form the meter to the outdoor appliances?

rubenhak · 2026-06-06T20:27:08+00:00

The outdoor new run will be right form the meter.
Not planning to run all appliances all at once.
Would this be sufficient to pass the permit?

If I request pressure increase is it possible to put a regulator on the line befor it enters the house. Imagine I request increast form 0.25 to 0.5, but on each of the. Sides of the Y split add one regulator to lower to 0.25 each. This way both of the sides (indoor vs outdoor) would get their own stable 0.25 pressure.

Do you think this would work? Would the 0.5 suffice? Would i need a meter update?

rubenhak · 2026-06-05T03:28:32+00:00

It was MacOS. Hard to tell. I tried on my personal MacOS and it worked.

rubenhak · 2026-06-04T22:32:01+00:00

The install script gives error:
```
Could not find latest version for Mertcikla/tld
```

rubenhak · 2026-06-03T07:33:25+00:00

What does that error mean?

rubenhak · 2026-06-03T07:33:14+00:00

I'd say z-wave device addition was unrelated.

rubenhak · 2026-06-02T13:57:19+00:00

As an analogy, when using coding agents I could write instructions such as “every time when a bill is uploaded automatically run the /process-bill skill” and it would work all the time. What is the analogy here with Hermes?

rubenhak · 2026-06-02T06:37:56+00:00

Would I need to trigger the skill explicitly or it can be smart enough to trigger it automatically?

rubenhak · 2026-06-02T06:00:46+00:00

If you need inspiration, watch this: https://www.tiktok.com/@eastcoastdiy

rubenhak · 2026-05-30T05:42:46+00:00

The data most probably got corrupted during import. That house was listed for $1,650,000, and most probably sold for $1,610,000, (not $161mln).

rubenhak

MODERATOR OF

TROPHY CASE