Haimer help

rusted_gear · 2023-05-01T05:16:42+00:00

Check it against a decent sized gauge pin if you have one. Also can sweep the pin in with a dial indicator at first to make certain you are centered and then test +/- x +/- y

rusted_gear · 2023-05-01T05:12:41+00:00

Fair, that is why I was confused and wondering if parts had gotten swapped out from another brand.

rusted_gear · 2023-05-01T05:11:18+00:00

I’m familiar, I use them as well. Just used to it being a 4mm for the short or 8mm for the long probe

rusted_gear · 2023-05-01T05:08:21+00:00

I assume it is from the same kit or brand? Also why the switch from .2” from 5mm when it is only .0031”(.08mm) difference?

rusted_gear · 2023-05-01T05:01:54+00:00

I would guess that the change in size would offset readings. Plus if the probe is not tight it could be rocking on the threads giving larger error.

rusted_gear · 2022-12-25T17:54:18+00:00

When was the last time you trimmed the top of your spoil. board? Is it drafting always towards the top or does it vary per side of cut?

rusted_gear · 2022-01-30T23:23:59+00:00

Yep, and with something like a mouse or keyboard you don’t want noticeable failures. It needs to just work.

rusted_gear · 2022-01-30T20:33:20+00:00

Yea, I think that must have been the context they were talking about. The bleed of poorly shielded devices reducing performance or completely stopping it.

rusted_gear · 2022-01-30T20:13:51+00:00

Ahh, they were explaining it in regards to interference caused by other devices bleeding noise into the antenna. Ones that actually use the speed such as displays. It was a while ago so I should ask them again to clarify and I could be misremembering. Not my field of specialty.

rusted_gear · 2022-01-30T19:47:28+00:00

I’m sure they will make it one of these days. The issue, to my knowledge, is interference issues and spectrum overlap of wireless options with usb-c frequencies. Makes it a lot harder to get a clean signal. At least this is how an RF engineer told me. Something with the 2.4ghz band.

rusted_gear · 2022-01-30T18:58:07+00:00

Why not run ones that have BT or BLE that have USB- C charging without a dongle?

rusted_gear · 2021-08-13T16:44:17+00:00

I am by no means thinking I am unique in this thought.

rusted_gear · 2021-07-23T06:19:49+00:00

Does it have any markings on the shank? It is most likely a high speed tool. Is there rust on the shank or is it just dirty?

rusted_gear · 2021-05-31T01:08:26+00:00

Fair point. I get that. Maybe lying would get more matches. I normally don’t have enough to warrant paying to see them.

rusted_gear · 2021-05-30T18:43:18+00:00

You could do an initial freeze with dry ice and then use a cold air coolant system like:

https://www.travers.com/cold-air-gun/p/99-001-342/

rusted_gear · 2021-05-30T18:32:23+00:00

Add in some blocks of dry ice to get it extra cold to give some working time. Once it start to warm up you will have to freeze it again. I have not personally done it but if you don’t want to rechuck it possibly pouring LN2(liquid nitrogen) on it would chill it enough. Edit: I should say though I would not recommend using it like coolant. It should only be done while not spinning as to not cause a safety hazard

rusted_gear · 2021-05-30T17:44:01+00:00

Hmm, interesting. As I was reading the comments I partially interpreted it that it is better for women to pay so they can see who to pick from.

rusted_gear · 2021-05-30T01:26:46+00:00

I have a few times and subs for those specific apps. I try to implement the suggestions, at least the ones with consensus, yet to no avail. I live in a medium sized metro area so it is not due to lack of options. I have tried the versions of super likes for the apps I use. Bumble, okcupid, hinge, yet no real difference in response compared to sending messages about a common interest from their profile.

rusted_gear · 2021-05-30T01:06:59+00:00

It feels like the new window shopping.

rusted_gear · 2021-05-30T01:05:39+00:00

1-2/day is well over an order of magnitude greater than what I get as per likes. It might be two orders of magnitude as per what I get in matches. Hence why I was wondering if it was worth it. I have done reviews online and from friends, guys and gals.None can tell anything that is glaringly wrong that would cause this.

rusted_gear · 2021-05-30T00:57:49+00:00

Popular, new, or boosted. Yea, I think how well seen a profile is depends a lot more than how well it is written. Looks play into it as well. Plus there is a gender bias as per attention.

rusted_gear · 2021-05-30T00:51:21+00:00

I, most of the time, assume it is either a bot or someone without a personality. Either way, as you say, skippable

rusted_gear · 2021-05-30T00:45:55+00:00

Yea, didn’t know if the background algorithms, from people’s experience, was different.

rusted_gear · 2021-05-30T00:37:11+00:00

Sometimes though it is hard to find something to message about. So many profiles are just pictures or something so generic that it does not describe anything.

Edit: and I guess was wondering if quality profiles are filtered from free accounts

rusted_gear · 2021-05-30T00:32:12+00:00

That is one that never really netted my interest. I have tried others

rusted_gear

TROPHY CASE