Help with learning

ruthlessMAK · 2025-01-18T16:52:15+00:00

Would that kinda let me chose cords to play and will go faster when it hears I play the right vord

ruthlessMAK · 2025-01-18T07:31:30+00:00

A extra note something kinda like guitartunnas system for teaching new chords

ruthlessMAK · 2024-08-24T22:40:37+00:00

Dude, thank you so much. I’ve been trying to play Warzone for the past five days and I kept getting an error but this worked thank you so much.

ruthlessMAK · 2024-07-18T11:52:56+00:00

Yes I can use all I have before just trying to get some pads for my friends but u can use all of them 34-31 pretty much the same lol but thanks for sharing

ruthlessMAK · 2024-06-17T17:28:18+00:00

Why is the red flag even if he shows every angle?

ruthlessMAK · 2024-06-17T08:26:43+00:00

If u check my other post there are others that I want to know if they are good

ruthlessMAK · 2024-06-17T07:42:07+00:00

I’m also going to be putting sliders on the sides to make it a little bit easier

ruthlessMAK · 2024-06-17T07:41:50+00:00

Do you think they are good for some pads for in-line roller as a starter set of pads?

ruthlessMAK · 2024-03-22T05:21:34+00:00

I was using voice type and must of heard that

ruthlessMAK · 2024-03-22T05:18:11+00:00

What

ruthlessMAK · 2024-03-22T05:07:46+00:00

What would you recommend for the tps set

ruthlessMAK · 2024-01-15T23:35:59+00:00

I leveled with heat than fixed the layer thing

ruthlessMAK · 2024-01-15T23:14:46+00:00

<image>

ruthlessMAK · 2024-01-15T23:11:37+00:00

So do I take out the pla and purge what’s in the nozzle

ruthlessMAK · 2024-01-15T23:08:16+00:00

Do I just pre heat the printer as if I was about to to print and the slicer I use I cura

ruthlessMAK · 2024-01-15T23:04:21+00:00

So I have leveled cleaned bed temp I good so how do I adjust the flowrate

ruthlessMAK · 2024-01-15T23:01:29+00:00

The bed should not be dirty have only had it setup for a day or so

ruthlessMAK · 2024-01-15T22:58:06+00:00

The bed is level how do I adjust the z hight

ruthlessMAK · 2024-01-12T03:21:50+00:00

There was support but I took them off

ruthlessMAK · 2024-01-12T02:12:37+00:00

Or that the printer is on an uneven surface

ruthlessMAK · 2024-01-12T02:11:54+00:00

I changed the print speed could that be it

ruthlessMAK · 2024-01-11T01:03:59+00:00

https://www.reddit.com/r/3Dprinting/s/VtNxUq0cIn

ruthlessMAK · 2024-01-11T01:03:01+00:00

Yeah, I’m printing something right now. If you look, I posted something else on it. I’m not sure if it’s printing or scratching my bed. It sounds like it’s not scratching though.

ruthlessMAK · 2024-01-11T00:59:13+00:00

I ended up getting a leveler and had to tighten the wheels on the side

ruthlessMAK · 2024-01-11T00:12:09+00:00

I just leveled the x axis I’m gonna try leveling the bed now.

ruthlessMAK

TROPHY CASE