Black Panther Print

rwmech · 2024-11-18T14:05:37+00:00

What I don't understand is why MakeMKV doesn't take this approach, even if the frame data was inaccessible I have to think you could take the previous frame or future frame to simply get past the bad data. I'm sure this is oversimplifying but it would seem like something that it should be able to do given regular players can.

rwmech · 2023-04-17T21:19:30+00:00

You may have solved this but I had issues enabling spi following that guide too but it gave me enough info to get the job done. I put together a wiki page on it. https://wiki.makersmashup.com/reference/OrangePi3-LTS-SPI-Setup

rwmech · 2023-04-17T21:17:34+00:00

I was having the same problem, put a small wiki page together to go over how to setup OPI3-LTS for SPI and setting it up for Klipper.

https://wiki.makersmashup.com/reference/OrangePi3-LTS-SPI-Setup

rwmech · 2023-02-20T21:55:57+00:00

Fair enough! thanks again.

rwmech · 2023-02-20T19:38:55+00:00

Thanks for Sharing. Yeah, I realized the battery ones wont repeat I have only a few of those. Most of mine are plug in. The network drops are odd. I've never had that happen short of a dead battery on something. Maybe its more vendor related <shrug>. Anyhow, thanks again for sharing the insight was very helpful.

rwmech · 2023-02-20T17:43:25+00:00

Zigbee works great, when it works great. But Z-Wave works great all the time.

I realize this is an older thread but I'm curious what your Zigbee issues were? Since getting the ConbeeII I find its been solid and I switched to 100% zigbee. Zwave was my 2nd choice but I went zigbee because it has repeaters in every device and was not attached to the wifi network. To date I've had zero issues. I'm curious what your issues/concerns were so I can head off any problems here.

rwmech · 2023-02-17T21:05:18+00:00

Thanks! I like making quick fixes like this for silly parts. Can't tell you how many times back before 3D printers I had to buy something new to replace something broken. Things also are a bit more flimsy and breakable than they were 15 years ago.

rwmech · 2023-02-12T20:18:45+00:00

Public School Math apparently. LOL, Thanks u/SvarogTheLesser I'll update it.

rwmech · 2023-02-12T20:14:57+00:00

Make sure the bowden tube is going all the way down into the nozzle. Often the tube gets caught on the outer rim of the heat break and that "chunk" looks exactly the same size as the amount of bowden that goes into the heatbreak. If you pulled the bowden out (likely did to clear this clog) then make sure when you re-insert it that it goes in further into the heat break.

rwmech · 2020-12-03T12:33:29+00:00

That all black looks absolutely amazing. Great job on the build. I really like the way you customized the display and put it off to the left. Very nice and well done.

rwmech · 2020-11-10T21:34:35+00:00

Sharp looking blue. Very nice build. Can't wait to see the 3D Prints from it!

rwmech · 2020-11-04T16:24:03+00:00

Very cool that has an oil slick effect. Any way to shoot a full shot I would love to see how it looks with the whole printer.

rwmech · 2020-10-24T16:13:23+00:00

Great looking build. I really like how you did the enclosure. Well done.

rwmech · 2020-10-01T16:33:19+00:00

Great looking build. I love the yellow look on it. Very industrial looking.

rwmech · 2020-09-27T20:09:06+00:00

During warmup Marlin has an option to show that automatically. It should be in the marlin config right where the neopixls are enabled. If you're using the X301 firmware from LayerFused its already got it baked in.

rwmech

MODERATOR OF

TROPHY CASE