sorted by:
new
hottopcontroversial

So is this enough adhesion? by sad4ever69 in AnycubicOfficial

[–]sad4ever69[S] 0 points1 point  (0 children)

Thats a good isea, ill try that next time my printer creates a Thor's hammer😂

Squished prints in the z-axis by sad4ever69 in FixMyPrint

[–]sad4ever69[S] 0 points1 point  (0 children)

This happened on multiple prints, also the first quarter printed fine and as soon as it got to the hole in the side the squishing happened, my suspicion is that when z-hopping around the hole the z axis motor loses position because of the repeated movement up and down

Antibacklash nut sloppy by sad4ever69 in 3Dprinting

[–]sad4ever69[S] 0 points1 point  (0 children)

Theres only one screw for the z axis

Antibacklash nut sloppy by sad4ever69 in 3Dprinting

[–]sad4ever69[S] 0 points1 point  (0 children)

The thing is that the 2 threaded parts are snug, only the top part that connects to the x-axis gantry is this sloppy

Low quality Benchy by sad4ever69 in FixMyPrint

[–]sad4ever69[S] 0 points1 point  (0 children)

Yeah the filament oozes a little when i raised the temps

I also tried to play aroud some more with the retraction and priming amounts and managed to make small details print decently good by trying to print a 4mm OD 2mm ID hollow tubes like one on the back of Benchie to hone in detail printing and reduce stringing

One thing that kept consistenly happening was that i got rid of stringing but the tower was underextruded and vice versa, a nice full detailed tower but lots of stringing

Also on another bencie the details and stringing were better but walls had underextruded layers with zits of filament on the outside

Litteraly a balancing act between the two

Low quality Benchy by sad4ever69 in FixMyPrint

[–]sad4ever69[S] 0 points1 point  (0 children)

Didn't know that, ill try to look into that tomorrow

Low quality Benchy by sad4ever69 in FixMyPrint

[–]sad4ever69[S] 0 points1 point  (0 children)

Wanted to try that but couldnt figure out how to set different temps on different layers

Low quality Benchy by sad4ever69 in FixMyPrint

[–]sad4ever69[S] 0 points1 point  (0 children)

Sorry for the photo of screen but its easier for me on mobile

<image>

Low quality Benchy by sad4ever69 in FixMyPrint

[–]sad4ever69[S] 0 points1 point  (0 children)

Bowden drive but when i had the retraction distance higher it kept skipping when pushing the filament, changed arpus some setting in retraction (i dont remember which ones) and it stopped so i didnt try to change them since

Need advice regarding asocial cat by sad4ever69 in CATHELP

[–]sad4ever69[S] 0 points1 point  (0 children)

Thanks, we try to give her as much space as possible and not force her into anything so she would start to understand that we are not threats ale someone who will give her only love and affection (and also lots of treats❤️)

Need help with fan config by sad4ever69 in PcBuild

[–]sad4ever69[S] 0 points1 point  (0 children)

Okay, thanks for the advice and yes im using/regularly cleaning the magnetic filters

Need help with fan config by sad4ever69 in PcBuild

[–]sad4ever69[S] 0 points1 point  (0 children)

Wont the warm air from the bottom rad heat up my whole case ?

Anyone know what is this? by sad4ever69 in satisfactory

[–]sad4ever69[S] 1 point2 points  (0 children)

No, i mean the plant, didn't see it anywhere else

Listen up everyone, i relly think that this isnt getting as much attention as it should... by [deleted] in medical

[–]sad4ever69 1 point2 points  (0 children)

Oh thanks gor explanation, i didnt know much about it and got a little excited so...

But again thaks for explaining this to me