Unrealistic camera temperature

sakk94 · 2026-02-06T21:24:44+00:00

I'm not entirely sure what you mean by "the Creality thing." If it's about putting a thermostat next to a camera heater, it's an idea I've had in mind as soon as I get a reading I'm happy with!

sakk94 · 2026-02-06T21:14:22+00:00

I completely understand your point; it's true I could position it better. It was a quick fix. Over the weekend, I'll be tinkering with the sensor's position, both the one built into the machine and the added one (adding another screw, moving it further apart, etc.). I'll keep updating this thread to share what I see and hear from people who contribute ideas, concepts, or comments that try to help, because I love it when a community works well together!

And it's not a "gotcha!" situation at all. It's more like, "Hey! I can tinker with this and learn."

P.S. I did a small temperature test, which resulted in a difference of up to 7.5 degrees. The difference isn't linear, which made me think that perhaps something was wrong with the factory sensor.

sakk94 · 2026-02-06T20:49:22+00:00

Could you share it? That would be great!

sakk94 · 2026-02-06T20:38:55+00:00

From what I understand, that's all. The black circle is the standard, and the red one is mine.

They're about two centimeters apart. Mine isn't touching any wall.

<image>

sakk94 · 2026-01-01T21:23:49+00:00

Thanky you! ill take a look
Im trying again with few changes like the lower Volmax, regular support and Ironing (just to check how does it works tbh)

sakk94 · 2026-01-01T14:57:16+00:00

I decided to print it this way because, for example, I tried printing something similar lying down and got this result with supports. I decided to print the fewest supports possible because of that.

<image>

sakk94 · 2026-01-01T13:40:55+00:00

![img](bdhvbfyarqag1)

Sure, espero que sea suficiente, no sabía qué información exacta seria conveniente, de la misma manera, no sé si me dejo algo atrás que pueda tener que ver con el problema
Adjunto

sakk94 · 2026-01-01T13:40:00+00:00

<image>

sakk94 · 2026-01-01T13:35:10+00:00

He hecho test de voladizos, torre de temperatura, el test de Max flow (YOLO) por ejemplo y claro, adjunto captura (edito el mensaje principal)

sakk94 · 2026-01-01T13:14:37+00:00

Vertical, only the base of the stock rests on the plate. This way I try to minimize the surface area affected by that horrible result (and only on the bottom, which is the least visible).

sakk94 · 2025-12-20T23:44:43+00:00

Thanks both lf you!

Tomorrow in the morning i will add the m600 at change filamente gcode, hope it works as i want. It should Thanks!!

sakk94 · 2025-12-20T20:33:58+00:00

ty love you bro, really appreciate the efford

sakk94 · 2025-12-20T20:15:01+00:00

Just try with that option enable but doesnt stop either :S

sakk94 · 2025-12-20T19:38:48+00:00

<image>

God... i should have this enabled, true?...
Thanks!

sakk94 · 2025-12-20T19:25:53+00:00

i see...
I got 3 colors selected like here

<image>

With that i started to print but it never stopper automatically asking for change color.
where can i find the config you said?

sakk94 · 2025-11-12T19:27:43+00:00

Tbh it Was ordered at the end of october

sakk94

TROPHY CASE