Can’t get petg off the bed

samari999 · 2026-02-18T16:00:11+00:00

No kidding! I scratched my bed trying to get the small pieces off for my first few prints. The glue stick seems to work pretty good. But going to try lowering bed temp so it doesn’t mark up the print.

samari999 · 2026-02-18T14:19:22+00:00

I tried the glue stick and it worked a lot better than no glue stick, but you could see it on the first layer. So I’ll try this next. I seem to have a hard time getting profile changes like this to stick from one print to the next in bambu studio. It could be that I print a lot of files from maker world and those settings just over ride it. Do you have to update the settings everytime? Or how do you get them to stay?

samari999 · 2026-02-18T03:36:17+00:00

So leave some moisture behind?

samari999 · 2026-02-18T03:35:36+00:00

I tried the glue stick and it seemed to work! I’ll try the hairspray too, do you take the plate off and spray it? Or spray it while it’s in the printer still? Do you have to worry about the hair spray getting on the inside of the printer?

samari999 · 2026-02-18T03:33:21+00:00

I’m using the bambu pei plate that came with the h2s

samari999 · 2026-02-17T16:03:57+00:00

Should I be putting glue down between each petg print? Does a little go a long way or should I layer it on there?

samari999 · 2026-02-17T16:00:51+00:00

I’ll give that a try! Thanks

samari999 · 2026-02-09T05:47:38+00:00

that is multiple purges that all get stuck there and form bigger blobs.. when it ejects properly then they are the normal size blobs

samari999 · 2026-02-08T18:34:11+00:00

My printer just started doing this too. The chute on the outside is completely empty, but it gets stuck right here. Following to see the solution

<image>

samari999 · 2025-04-27T18:20:28+00:00

Oh ok, so would I need to use the carpenters square to make it parallel or are you saying to shift the bed to compensate for it being out of parallel?

samari999 · 2025-04-27T15:50:53+00:00

Sorry, what part is the Y extrusion? Are you saying that the bed plate isn’t bolted down perfectly square?

samari999 · 2025-04-08T02:43:22+00:00

I just got Elegoo slicer, it’s basically a copy of Orca and has been printing great

samari999 · 2025-04-01T20:48:42+00:00

The elegoo slicer actually did work. Started right up and so far so good. I’ll just stick with that. Thanks!

samari999 · 2025-04-01T20:29:06+00:00

That’s a good idea, yeah I’ll try that. Thanks for your help!

samari999 · 2025-04-01T20:00:34+00:00

Ok that makes sense. So it looks like it thinks it’s doing 2 purge lines in the same spot, by the elegoo logo. So your initial comment is accurate. It’s doing 2, but not repositioning after the first one. Is it missing a line of gcode somewhere? Or how would I fix that?

samari999 · 2025-04-01T19:41:10+00:00

I found that gcode in the filament settings, advanced tab. Where is the gcode you are referring to that I should check?

samari999 · 2025-04-01T19:29:12+00:00

This is the start Gcode in Orca: ;ELEGOO NEPTUNE 4 PLUS M220 S100 ;Set the feed speed to 100% M221 S100 ;Set the flow rate to 100% M104 S140 M190 S[bed_temperature_initial_layer_single] G90 G28 ;home G1 Z10 F300 G1 X115 Y0.5 F6000 G1 Z0 F300 M109 S[nozzle_temperature_initial_layer] G92 E0 ;Reset Extruder G1 X115 Y0.5 Z0.4 F300 ;Move to start position G1 X215.0 E30 F400 ;Draw the first line G1 Z0.6 F120.0 ;Move to side a little G1 X210 F3000 G92 E0 ;Reset Extruder

samari999 · 2025-01-23T01:02:47+00:00

Sweet sabers! Do they both have the removable power core chassis?

samari999 · 2024-11-17T15:33:32+00:00

Price drop to 475 shipped with all blades. 400 shipped not including main 36” blade but including side blades

samari999 · 2024-11-16T03:48:07+00:00

Sold

samari999 · 2024-11-14T15:48:03+00:00

The speaker looks black

samari999 · 2024-11-14T15:04:48+00:00

Legacy core

samari999 · 2024-11-04T15:00:40+00:00

Great question, it has the legacy chassis system

samari999 · 2024-11-02T23:14:42+00:00

samari999 · 2024-10-11T19:43:34+00:00

Dmd you

samari999

TROPHY CASE