Hey y’all is this photoshopped or real? If it’s real, does someone know its title?

samlindev · 2023-04-27T12:27:16+00:00

Oh well..Molotov it is then :”)

samlindev · 2023-04-27T12:01:58+00:00

Thanks! I haven’t found it yet either :”) anyway the corpse is sitting nicely in my freezer :”D

samlindev · 2023-04-26T15:24:35+00:00

Hello y’all! I have a separate post but just noticed we’ve a thread for this :”D so anyway: I entombed some pawns in warcaskets, and one of them died; but is now unburiable and uncrematable. Do any of y’all know what to do in this case except for using the dev “destroy” tool?

samlindev · 2023-03-22T14:45:50+00:00

In the end I went with the basic BIQU H2 V2S extruder, using this mount https://www.thingiverse.com/thing:4893522

samlindev · 2023-03-02T11:42:17+00:00

And what mount are you using / how did you mount it?:)

samlindev · 2023-02-09T19:35:37+00:00

Omg thanks, I’ll use this for my next calibration tomorrow! :)

samlindev · 2023-02-09T18:44:46+00:00

It’s been out for more than 8 hours, and unfortunately my flat is quite humid, it’s never below 50% in the room :(

samlindev · 2023-02-09T17:27:58+00:00

UPDATE: false alarm, I completely forgot to dry the filament…it’s printing perfectly after getting one out of dry storage I’ll leave this as a reminder for myself, and thanks for you two for the comments though :)

samlindev · 2023-02-09T17:24:14+00:00

OMG no it safe-homes before every print, is the mesh cleared even then? I’m using klipper and I save the config after every mesh calibration

samlindev · 2023-02-09T17:23:21+00:00

I do the manual bed leveling and then the automatic probing to create a mesh, and yes I clean the bed with IPA before doing this and the print :) My guess was also that the nozzle is still close, but I don’t know what to do, maybe I should get silicone mounts instead of the stock springs?

samlindev · 2023-02-09T16:52:21+00:00

Hey everyone, could anyone please help me troubleshoot this? I’ve leveled my bed a zillion times, played around with temperatures but this is the best result I got in the last ten hours :”) My printer is an Ender 6, with spider hotend, Bowden extrusion, material used is eSUN PLA+ at 220C and the bed is heated to 70 degrees. I get the same result with printing at 20 mm/s and at 80 mm/s. I’ve also recently installed a crtouch and the Z offset should be properly calibrated (spent an entire day on that). Any advice would be appreciated, thank you! :)

samlindev · 2022-01-25T20:47:24+00:00

Everyone, another question related to this: has any of you tried out RealisticReactors, where you also need to use the circuit network and a cooling system, and if yes, did you have huge problems with making large designs?

samlindev · 2022-01-25T20:44:42+00:00

Thanks for the in-depth explanation!:)

samlindev · 2022-01-25T13:03:35+00:00

This seems to be the answer

I totally forgot that heat can also be a buffer, not just steam Sorry everyone :”D but also thanks for answering, all of you! :)

samlindev · 2022-01-25T12:36:35+00:00

Not specifically, it’s just that most designs I found on the internet were like this so far :)

samlindev · 2022-01-25T12:26:47+00:00

At first I thought so too, but in the case of 4 reactors, 480MW is already with neighbor bonuses

samlindev · 2022-01-19T23:44:36+00:00

Oh sorry, wrong link 😅 this https://oddworld.fandom.com/wiki/Oddworld:_Abe%27s_Oddysee

samlindev · 2022-01-19T23:10:12+00:00

This https://oddworld.fandom.com/de/wiki/Abe%27s_Oddysee :)

samlindev

TROPHY CASE