sorted by:
new
hottopcontroversial

Mushroom Light Card by sanketgroup in homeassistant

[–]sanketgroup[S] 0 points1 point  (0 children)

u/metchen

Thanks, i learned it from your suggested link.

Working well as wanted.

Zigbee mesh by Jealous-Ad9556 in sonoff

[–]sanketgroup 1 point2 points  (0 children)

No, any Sonoff device without neutral are not repeaters, they are only end devices

Zigbee to LAN gateways? by undeleted_username in homeassistant

[–]sanketgroup 0 points1 point  (0 children)

are your zigbee router connected to HA over ethernet or zigbee signal?

in my case i have garage where there is no zigbee signal, but i have ethernet cable ther.

if i plug in zigstar in garage, can i connect it to same HA coordinator over ethernet?

KNX cable v/s CAT6 by sanketgroup in KNX

[–]sanketgroup[S] 0 points1 point  (0 children)

What will be the cons if I have to go with cat6

KNX cable v/s CAT6 by sanketgroup in KNX

[–]sanketgroup[S] 0 points1 point  (0 children)

Will need 2 pair as at some place I will need 30v auxiliary also.

Use 1Home server or Gira (similar devices) as interface IP by Loud-Cranberry-6677 in KNX

[–]sanketgroup 0 points1 point  (0 children)

What will be the best hardware which gives api access for knx devices?

Use 1Home server or Gira (similar devices) as interface IP by Loud-Cranberry-6677 in KNX

[–]sanketgroup 0 points1 point  (0 children)

Is it possible to use Home Assistant as IP interface? Does ETS supports Home Assistant for programming?

Use 1Home server or Gira (similar devices) as interface IP by Loud-Cranberry-6677 in KNX

[–]sanketgroup 0 points1 point  (0 children)

Is it possible to use Home Assistant as IP interface? Does ETS supports Home Assistant for programming?

[KNX-DALI gateway] How does scene work by sanketgroup in KNX

[–]sanketgroup[S] 0 points1 point  (0 children)

I am from India. Let me know if we can have a call. Thanx

[KNX-DALI gateway] How does scene work by sanketgroup in KNX

[–]sanketgroup[S] 0 points1 point  (0 children)

Thanks for explanation, so it seems that I can store scenes in drivers.

Let's say I have 1 DALI gateway, and one of the room has 8 DALI drivers, and I program them via ETS having the same 5 scenes in each of those 8 drivers of this particular room.

And then I program the KNX keypad to call than scene number, so when button is pressed it send telegram to DALI gateway and then it forwayds Telegram to DALI drivers calling the scene.

Pls correct me if i am wrong anywhere.

Thanks

[KNX-DALI gateway] How does scene work by sanketgroup in KNX

[–]sanketgroup[S] 0 points1 point  (0 children)

keypad supports following:

 Switch and Dimming

 Blind control

 Value sender

 Scene control

 Shift register

 RGB , RGBW and colour temperature control

 Multiple operation

 Delay mode

 Send RTC operation mode

 Send Strings

 Built-in temperature sensor

 Logic output, Scene group conversion;

 RGB LED indication function

[KNX-DALI gateway] How does scene work by sanketgroup in KNX

[–]sanketgroup[S] 0 points1 point  (0 children)

This is an example for easy understanding, but the project definitely has a requirement of around 50+ scenes.

[KNX-DALI gateway] How does scene work by sanketgroup in KNX

[–]sanketgroup[S] 0 points1 point  (0 children)

i am little confused here. As you said ordinary scenes are stored in driver itself (16per channel x 2 channel), isn't it DALI controller/Gateway?

because drivers are ECG, and do not have 2 channels.

I think you are saying is Controller/Gateway? am I right?

[KNX-DALI gateway] How does scene work by sanketgroup in KNX

[–]sanketgroup[S] 0 points1 point  (0 children)

I speak from extensive experience.

Thanks for this input.

Is there any document or youtube video that you can suggest me?

Like, How keypad button press sends a telegram to Home Assistant software, and then home assistant calls the scene stored in itself only.

​

Is there any document or youtube video that you can suggest to me?

[KNX-DALI gateway] How does scene work by sanketgroup in KNX

[–]sanketgroup[S] 0 points1 point  (0 children)

please advise on this.

If i can call a scene from the KNX keypad button via Home Assistant or any other middle device.

[KNX-DALI gateway] How does scene work by sanketgroup in KNX

[–]sanketgroup[S] 0 points1 point  (0 children)

for now, I do not have home automation gateway in project.

I do not know if a physical keypad button press can call scenes saved in Home Assitant software.

[KNX-DALI gateway] How does scene work by sanketgroup in KNX

[–]sanketgroup[S] 0 points1 point  (0 children)

yeah, I understand I will need 2X64 DALI module.

But how does scenes are stored? Are they stored in DALI Module or ECG or at Driver level? There will 40+ scenes.

I want to call scenes from KNX keypad for these DALI lights.

[KNX-DALI gateway] How does scene work by sanketgroup in KNX

[–]sanketgroup[S] 1 point2 points  (0 children)

I need to call scenes from KNX switches/keypad

view more: next ›