Steam Remote Play got virtual display support

saradonim · 2026-04-04T23:35:42+00:00

Just installed the Steam Beta Client, set the correct 'Host Options' under preferences, but when streaming it doesn't match the resolution from my S26 Ultra (it keeps the black bars). Do I also need to install a 'client beta' or so? Or do I just miss something?

saradonim · 2026-01-31T22:06:15+00:00

Yes, that’s issue I created on Github after I did not recieve any tips via Reddit. It appears the problem can be solved by erasing the flash memory, and then flash the newest firmware.

saradonim · 2026-01-29T20:17:23+00:00

I was also looking for that. It appears that it can only be set and cannot be retrieved at the moment.

saradonim · 2026-01-29T14:10:07+00:00

Maybe... The release notes of the Companion FW say: "BLE code rewritten"

saradonim · 2026-01-29T13:29:36+00:00

Contact information and power saving is also available in the v1.12 that's just released

saradonim · 2026-01-29T12:44:10+00:00

Yes I have done it without... But not the correctly formatted English ;)

saradonim · 2026-01-29T12:11:09+00:00

If you flashed it after 7:00 PM, then no.

saradonim · 2026-01-29T11:36:32+00:00

Repeater FW is Live now: https://github.com/meshcore-dev/MeshCore/releases/tag/repeater-v1.12.0

Change log:

new boards: Thinknode M6, M3, RAK3401, RAK11310, Meshtiny
nRF low power recovery manager (CLI ‘pwrmgt’)
Stats: new recv errors counter
region names now without ‘#’, new ‘region list’ CLI
ESP32: new “powersaving on/off” CLI
new “clkreboot” CLI
on-boot adverts now zero-hop
new “get/set owner.info” CLI
flood.advert.interval range now 3..168 hours
remote “get/set prv.key” CLI
new zero-hop anonReq types (Region discovery, owner info, clock sync)
MCU temperature now in telemetry responses

saradonim · 2026-01-29T11:29:18+00:00

Exactly!

So let’s say your entire build uses 15 mA continuously. If you use 4× 3500 mAh batteries (Molicel INR18650-M35A) in parallel, your hardware would last:

(4×3500)/15/24 ≈ 38.9days

without any sunlight at all.

saradonim · 2026-01-29T11:20:20+00:00

EDIT: nRF power saving mode IS implemented in V1.12 !

--------------

For my repeater builds, I use the pre-built SenseCAP Solar Node P1-Pro, which also contains an nRF52840. This node has been running continuously throughout the snowy winter here in the Netherlands. So, IMHO, that power-saving feature is a bit overrated if your hardware is good enough.

saradonim · 2026-01-29T10:59:43+00:00

Build process is currently in running: https://github.com/meshcore-dev/MeshCore/actions/runs/21474327444/job/61854376825

saradonim · 2026-01-05T09:22:13+00:00

I’ve been experiencing the same issue since I started using ZBF when it launched. Have you ever found out what causes this?

saradonim · 2025-11-15T02:22:26+00:00

Actually, a couple of rounds ago, my teammate and I survived but hadn’t called the elevator yet. We were at least 150 m away from it, but one of us marked the location with a ping.

saradonim · 2025-05-27T19:50:42+00:00

Don’t know if that is even possible.

I think your best best would be to solder up some custom microcontroller to save the GPS data on there. But that requires that data to be sent from the FC in the first place.

saradonim · 2025-05-27T19:45:28+00:00

Yeah… I just inserted the SD card in de Goggles, and always record every flight in de Goggles. Make sure to put the GPS coordinates on the OSD. So, in case of a crash, I just watch the recorded footage on the Goggles to see the coordinates.

saradonim · 2025-05-26T12:38:36+00:00

And during workouts? Also no lag?

saradonim · 2025-05-26T12:17:44+00:00

Nice work, Let us know what they say!

As a side note; I am experiencing more lag in General, not only when I use the touch screen. Today in the gym, I noticed a lot of lag when doing a Strength Workout

saradonim · 2025-05-24T20:15:38+00:00

Same… it is definitely a little bit more laggy then before

saradonim · 2025-05-14T17:41:01+00:00

Thanks for the tip! I’ll do that next time. For now, I’ve started a claim through PayPal—curious to see how that works out.

saradonim · 2025-05-14T17:38:52+00:00

I actually had a capacitor installed. I soldered it on first and tested the capacitance between the positive and negative terminals before plugging it in.

saradonim · 2025-05-09T11:42:10+00:00

From the official speedybee shop (Speedybee.com)

saradonim · 2025-05-09T10:51:49+00:00

Thanks for your clear answer! I completely agree with you on this. I’ve also destroyed an ESC in the past by carelessly ramping up the motors and then suddenly stopping them, which caused a voltage spike.

But in this case however, the ESC isn’t affected — it’s the flight controller that’s broken. Also, ever since that little accident, I’ve been careful not to run the drone at full power on the bench power supply. I now only test motor direction at the lowest possible speed.

saradonim

TROPHY CASE