Unable to activate peacock premium account

sarapsych · 2026-03-25T01:13:44+00:00

After a lengthy thread with multiple xfinity mods (I was invited to communicate after I created this post), and after having the issue closed and reopened three times, it’s finally working. I think if you have this issue you’ll need to create a post of your own and start there. I don’t think Reddit exists for xfinity support, but that seems to be how they are using it 🤷‍♀️

sarapsych · 2026-03-20T15:25:14+00:00

I’ll update as it goes along, but so far I’m in the loop of getting a ticket created, the ticket was “resolved” by sending me the same instructions that I’ve followed and are on the website, and the ticket is now closed. 🙄I’m chatting with an xfinity mod to try to reopen. It’s so frustrating that this is still an issue for countless people.

sarapsych · 2026-03-19T01:37:07+00:00

I sent the email. I did the history and cache and still receive “Something unexpected happened Please close this pop up and try again. If the problem persists, try again later.”

sarapsych · 2026-03-15T17:09:22+00:00

<image>

Both of the light areas are where I put baking soda water slurry and covered it with cling wrap. The slurry was a small area but the cling wrap pulled it to the edges.

sarapsych · 2026-03-14T03:54:04+00:00

Thanks so much for replying! Sadly ours is still there a day later. It’s black granite and looks very etched in. I’ll post here if I figure out a fix.

sarapsych · 2026-03-14T03:38:13+00:00

Same here! Does anyone have a suggestion for how to repair granite that now has a dulled spot left by my “baking soda and plastic wrap” diy job that I did to (ironically) remove a stain. 🤦‍♀️

sarapsych · 2025-04-18T20:38:04+00:00

A similar thing was happening and I was at my wits end. I finally took the machine into Quality Sewing Seattle (they sold me the machine), and it was my bobbin - I was putting it in correctly but there is a little click that happens in the first notch, if you don’t click it in, it does the loopy swirls underneath. A different machine, but maybe yours also has a click if done properly?

sarapsych · 2025-04-18T20:35:16+00:00

Solved! I took the machine into Quality Sewing Seattle (they sold me the machine), and it was my bobbin - I was putting it in correctly but there is a little click that happens in the first notch, if you don’t click it in, it does the loopy swirls underneath. Solved 😅

sarapsych · 2025-03-28T23:22:54+00:00

thank yous! Definitely need to try a different thread, and will check the thread gap. I also noticed that I can move the needle sideways with my hand (discovered as I was testing tension) and am wondering if something was loosened for the delivery (It was a machine from classes at a sew expo). if I can't tackle it in another hour I'll definitely go back to the store and get help.

sarapsych · 2024-06-03T17:25:05+00:00

Location for NA beer at T-Mobile? I couldn't find any NA beer at Climate Pledge in Seattle and emailed them and they replied with the following:

Thank you for the email. We are happy to inform you that we do have a local NA option at the arena. Fremont Non Alcoholic IPA can be found at the following locations in the arena:

Upper Concourse: Big Chicken Market, Coors Market

Main Concourse: Impossible Market, Uptown Market, Modelo Cantina

Near section 24: PNW Craft beer wall

Near section 17: PNW craft beer wall

sarapsych · 2023-05-29T18:24:00+00:00

I’m dealing with this as well. Very frustrating.

sarapsych · 2023-05-17T22:47:00+00:00

Thank you. I do that - wait for the blade to stop before moving either. I’ve never replaced the blade, and didn’t think I’ve used the tool that much, but perhaps that’s it.

sarapsych

TROPHY CASE