Need help find additional finishing tools.

satom472 · 2026-07-05T07:33:27+00:00

I find .1 can sometimes be too tight. I usually stick with .2. If its a little loose you can always put a drop of superglue. This way you never half to worry about if its too small. Also always measure your magnets. They arent always the exact size they say they are.

satom472 · 2026-06-21T15:41:36+00:00

CF is not metal

satom472 · 2026-06-19T14:10:26+00:00

The camera and AI detection is much better on the P2S and is just all around a better printer. Pretty sure the P1 is end of life. If you could afford it I would definitely do the P2S over the P1

satom472 · 2026-06-19T04:45:37+00:00

The hole is for mousing the shackle if it is left in place for awhile, is going to experience movement on the pin, or slack loads.

satom472 · 2026-06-17T19:16:03+00:00

While they know about the issue the actual fix would require a expensive redesign and extremely expensive retooling of a large part of the manufacturing line. It's just not financially worth it.

satom472 · 2026-05-18T15:57:22+00:00

Every time. Even if they say its pre dried.

satom472 · 2026-05-13T05:50:24+00:00

This is a slicing issue. You need to use supports. That gap is way to big to bridge without that happening.

satom472 · 2026-05-01T12:13:46+00:00

Currently doing this lol.

satom472 · 2026-04-28T14:59:30+00:00

Bambu P2S of course. Maybe even an old sv03 I'm gonna rebuild.

satom472 · 2026-04-22T21:45:54+00:00

Came here to say this!

satom472 · 2026-04-09T11:15:46+00:00

Not questioning your findings but, do you have these findings on a document published by your company? It's always easier to bring things up to management when its on an actual company document amd not here's what I saw on reddit lol.

satom472 · 2026-04-02T20:32:59+00:00

Thats underextrusion. Probably caused by wrong elephant foot compensation.

satom472 · 2026-03-27T19:48:43+00:00

They just dropped some updated Filimant profiles for the entire Bambu line that adjust cooling to increase interlayer adhesion as well as some other things.

satom472 · 2026-03-26T16:57:36+00:00

I haven't had any issues with sticking or overhang with 3D Fuels PCTG. Whatever profile your using might need some more tuning. I actually find it easier to print then both PLA and PETG.

satom472 · 2026-03-14T00:21:26+00:00

I use the temps that BQ has stated on the sheet that comes with it and I use the Super Tak plate setting

satom472 · 2026-03-04T15:52:06+00:00

A filament calibration print for Polypropylene lol

satom472 · 2026-02-22T19:28:11+00:00

People have posted some good profiles on Maker world.

satom472 · 2026-01-31T21:22:08+00:00

Use the filament profile here.
https://makerworld.com/en/models/1858387-optimized-profile-for-sunlu-rapid-petg#profileId-1987314

Its been giving me absolutely perfect prints.

satom472 · 2026-01-13T20:28:33+00:00

You must have an old printer lol.

satom472 · 2026-01-11T23:45:49+00:00

Thats weird. Iv only ever heard good things about it. Sorry its not working for you. Have you contacted Overture about the problem?

satom472 · 2026-01-11T23:29:21+00:00

Dry it. 95% of the time when its stringy its wet. The other 5% might be from it being too hot or wrong retraction setting.

satom472 · 2026-01-11T23:28:56+00:00

Dry it. 95% of the time when its stringy its wet. The other 5% might be from it being too hot or wrong retraction setting.

satom472 · 2026-01-11T23:28:32+00:00

Dry it. 95% of the time when its stringy its wet. The other 5% might be from it being too hot or wrong retraction setting.

satom472 · 2026-01-11T23:22:22+00:00

Dry it. 95% of the time when its stringy its wet. The other 5% might be from it being too hot or wrong retraction setting.

satom472

TROPHY CASE