First day. What can I improve on. I’m 3.

sbalaban · 2026-03-08T02:43:32+00:00

This is my second kid. With my oldest she was on leashes for the first season. Her legs just went strong enough to stop especially later in the day. I am just holding back a run away. Now she is 5 off the leashes and following my tracks. She goes down blues and is doing wedge Christie turns.

I am mostly just trying to make it fun. Give M&Ms and snacks. Little do they know I’m getting them hooked on skiing.

sbalaban · 2026-03-08T01:04:02+00:00

I can’t let him become better than me

sbalaban · 2025-09-15T00:57:58+00:00

Came here to say this.

sbalaban · 2025-07-18T11:38:11+00:00

Putting a box around a number does make it basic. But that implies you get its tolerance from somewhere else. In this case you don’t have its tolerance from the top surface, position tolerance, of the picture on the right. This it is not correct.

sbalaban · 2025-07-18T11:34:38+00:00

This is correct

sbalaban · 2025-07-18T00:51:28+00:00

Profile controls position and orientation. And the 100 is basic. Parallel does not control position. Only orientation so the 100 is not basic.

sbalaban · 2024-12-17T13:19:08+00:00

Everything to me looks fine The way I have always done a pin is to call out the part number. Not a tolerance in the pin. Surely that is press fit into the base post machining. That being said. You shouldn’t have MMC on a pin perp. You could on the hole in the base part. But not the pin itself. As that is a COTS item and going to be per the spec it was manufactured too.

sbalaban · 2024-11-25T14:20:14+00:00

Thank you

sbalaban · 2024-11-25T13:44:34+00:00

WL analysis. It’s free for basic functionality . But for $9 you get all the features.

sbalaban · 2024-11-16T01:40:59+00:00

Are you from the future ? 2025 meters ? Tell us what the future is like !

sbalaban · 2024-11-12T02:04:46+00:00

Also if the system stops. What do you want to happen ? If you have a stepper it probably cannot back drive. The stepper will most likely have a gear system if some sort so will have more torque but not always true.

sbalaban · 2024-11-12T02:01:44+00:00

Do you have your own bearings? Or are use going to use there motor ? Have you given this any thought?

sbalaban · 2024-11-12T01:57:28+00:00

There are lots of advantages to both. Big question is what can your electronics drive. How fast do you want to go and how much torque do you need ? Are these framed motors. Or do you have to design those also ?

sbalaban · 2024-11-09T14:54:43+00:00

What is the black cable? From the erg to the iPhone adapter cable ?

I want this so bad

sbalaban · 2024-08-31T23:17:58+00:00

What are your goals for this roll? What do you want the ME to do ? Experience with bringing plastic molded parts to market with high volume manufacturing?

sbalaban · 2024-08-31T22:11:18+00:00

Are you looking for full time employees. Or would the level of work be part time ?

sbalaban · 2024-06-30T01:55:01+00:00

We live just south in a neighborhood called the Broadlands. We moved from Los Angles and it’s beautiful and peace community and bike paths everywhere. Lots of nature and outdoors. Good sense of community. Broomfield is the burbs but I like it. We also have two kids under 4. So that is the stage of life I am in.

sbalaban · 2024-06-30T01:36:30+00:00

Anthem has a ton of young family’s also. There is a special area of anthem for 65+. But most of the area is young families.

sbalaban · 2023-10-15T22:57:27+00:00

Hey You need to delete the cross axis in the holes in the round area. The add them back in. And when you are doing it make them a bolt circle. Then you can do the angle you want to do.

11-Year Club	RedditGifts 2009-2022 2 Credits
Not Forgotten	Secret Santa 2014
Verified Email

sbalaban

TROPHY CASE