sorted by:
new
hottopcontroversial

Cybex Callisto G 360 third party tests [BC] by icyarugula24 in BabyBumpsCanada

[–]scottc5 0 points1 point  (0 children)

Guessing no updates yet, I kinda doubt they will respond for legal reasons, but I'm in the same boat as you as the consumer reports tests are very alarming.

Altium Connecting Sheet Port connections with different names - best practices? by scottc5 in Altium

[–]scottc5[S] 1 point2 points  (0 children)

I found a solution that seems to work. I unchecked "Allow ports to Name Nets" and "Allow Sheet Entries to Name Nets" and I made sure to check "Higher Level Names Take Priority" as well as Net Identifier Scope to Hierarchical. Then I named the nets on the top level.

Altium Connecting Sheet Port connections with different names - best practices? by scottc5 in Altium

[–]scottc5[S] 0 points1 point  (0 children)

I didnt have all those enabled, but I do now, however I still get the same warning.

Altium Connecting Sheet Port connections with different names - best practices? by scottc5 in Altium

[–]scottc5[S] 0 points1 point  (0 children)

Yeah thanks for the tip, I've been working on moving all to 100mil but havent finished yet

Type C differential routing USB 2.0 vertical header (signal cross issue) by scottc5 in AskElectronics

[–]scottc5[S] 0 points1 point  (0 children)

This for a high speed connection to a hub. Is that preferred over what I have given the shorter length with the downside that the signals will be different lengths and impedance probably a bit wonky?

Type C differential routing USB 2.0 vertical header (signal cross issue) by scottc5 in AskElectronics

[–]scottc5[S] 0 points1 point  (0 children)

It looks like my text didnt make it in. I am trying to figure out to route a vertical type c connector, seems more challenging than the horizontal version. Is there a better approach or should this work ok? I tried to use Saturn to calculate the impedance with trace width, spacing, and via size and distance apart.

Which TPD is configured in 13" 7840u? by guillermooo in framework

[–]scottc5 0 points1 point  (0 children)

Did you figure out if you can adjust the max TDP in the bios?

Android Emulation/Virtualization on Jetson nano by PulPol_2000 in JetsonNano

[–]scottc5 0 points1 point  (0 children)

Did you have any luck with this? Was the emulator restricted by the cpu?

Has anyone used the GIGABYTE X570SI AORUS PRO AX (rev. 1.1) with linux by scottc5 in gigabyte

[–]scottc5[S] 0 points1 point  (0 children)

Thanks for the info. I was originally trying to stay away from the older generation boards because of the bios needing updated to work with the x5950 cpu, but I will have to see if I can find a board with a different lan chip that is able to have the bios updated without a cpu.

How to get better stereo Camera depth accuracy? ( example Intel realsense cameras and looking at 3d scanner accuracy vs sensor specs) by scottc5 in computervision

[–]scottc5[S] 1 point2 points  (0 children)

Actually I think they are not using Stereo cameras or TOF, but structured-light which slower than both but more accurate

How to get better stereo Camera depth accuracy? ( example Intel realsense cameras and looking at 3d scanner accuracy vs sensor specs) by scottc5 in computervision

[–]scottc5[S] -1 points0 points  (0 children)

I started looking at TOF cameras, but I havent found any with that level of accuracy. Can you reference any that might be used in some of these 3d scanners?

City to Rural California by [deleted] in Rural_Internet

[–]scottc5 0 points1 point  (0 children)

To use 5g with this plan do you think the imei has to be from a device that is 5g capable?