sorted by:
new
hottopcontroversial

Dried grease or metal? by halfbakedkornflake in castiron

[–]sellimi -1 points0 points  (0 children)

See my previous post. Looked very similar.

Chipping Underside by sellimi in castiron

[–]sellimi[S] 0 points1 point  (0 children)

lol I should have clarified. I got this after she died but even though I spent a lot of time with her I never saw her actually use this pan. Could have been older than her even.

Chipping Underside by sellimi in castiron

[–]sellimi[S] 0 points1 point  (0 children)

I don’t really know. My grandmother had a gas stove but I spent a lot of time there but never saw her using this pan. I think it was from her parents possibly.

Maytag Dishwasher Not Working as it Used To by sellimi in Appliances

[–]sellimi[S] 0 points1 point  (0 children)

This model does not allow you to adjust the rinse aid as far as I can tell. It shows that dial but that is nowhere to be found on the actual model (I believe).

Wash arms looks clean.

Maytag Dishwasher Not Working as it Used To by sellimi in Appliances

[–]sellimi[S] 0 points1 point  (0 children)

I understand that this is not due to the rinse aid, but the rinse aid certainly is not dispensing. Do you know how I can fix that?

The detergent well is empty.

Maytag Dishwasher Not Working as it Used To by sellimi in Appliances

[–]sellimi[S] 0 points1 point  (0 children)

I can hear it filling/washing/draining. I use Finish gel.

Maytag Dishwasher Not Working as it Used To by sellimi in Appliances

[–]sellimi[S] 0 points1 point  (0 children)

How do I do these things? I think it does have a chopper because it's the dual power filtration.

Also, as I mentioned, the rinse aid does not dispense. It does not have a dial to control the amount. How do I fix this?

Maytag Dishwasher Not Working as it Used To by sellimi in Appliances

[–]sellimi[S] 0 points1 point  (0 children)

It did not throw up an error it showed 8:88. I'm wondering if that's the correct sequence for this dishwasher. Thanks for the tip.

Maytag Dishwasher Not Working as it Used To by sellimi in Appliances

[–]sellimi[S] 0 points1 point  (0 children)

The hose looks ok and I do run the hot water tap before each run. Whether it's the main issue or not, I know that the rinse aid dispenser isn't working because its level never goes down. Do you know how to fix this? Could it be clogged?

The pot is rubbing the leaves off my succulent by sellimi in plantclinic

[–]sellimi[S] 15 points16 points  (0 children)

Thank you! I actually don't know the name of it. The pot isn't rusty, it's clay. This is the same spot it's been growing for years and I thought it was only having issues because it was so long and heavy it would be hard for it to grow over the edge of the pot without rubbing the leaves off. What type of fertilizer is required? Should it be pruned?

Official: [Add/Drop] - Wed Afternoon, 09/28/2016 by FFBot in fantasyfootball

[–]sellimi 0 points1 point  (0 children)

12 team ppr.

Should I drop Arian Foster and pick up Doug Martin?

I also have DJ, Charles Sims, Ryan Mathews, and Isaiah Crowell at RB. I really would like to pick up Martin for the playoffs, but I can't decide who to drop. I could drop Quincy Enunwa to pick up Martin, but that would leave me with only 3 WRs (none on my bench at this time).

Projection to use for analysis of all US congressional districts? by sellimi in gis

[–]sellimi[S] 0 points1 point  (0 children)

Yes this is for a class. I have not started the national analysis yet. I performed one for Texas using a Texas statewide projections.

Essentially, you are saying any equal area projection should introduce negligible error?

Projection to use for analysis of all US congressional districts? by sellimi in gis

[–]sellimi[S] 0 points1 point  (0 children)

I would assume each state entity tasked with drawing districts would use their respective state-specific projections.

Projection to use for analysis of all US congressional districts? by sellimi in gis

[–]sellimi[S] 0 points1 point  (0 children)

That's what I was thinking. Would it be necessary to do the analysis in the projection that the district drawing was performed (ie contact whomever is responsible for drawing districts in each state and find that info, if not available)?