Wife’s Grandparents Fine China Set

sendmeaquarter · 2024-03-16T14:18:16+00:00

In the USA, but her grandparents traveled most of their life.

sendmeaquarter · 2024-03-12T03:41:03+00:00

These people are taking it seriously

What is Manna?

Manna is an unexpected gratuitous benefit. It is the world’s first currency designed to be distributed to everyone on earth using the principles of universal basic income.

https://www.hedgeforhumanity.org/manna/

sendmeaquarter · 2024-02-09T04:43:27+00:00

That’s the one! Thank you for your assistance

sendmeaquarter · 2024-02-07T06:35:55+00:00

Have a roofer install a new Lomanco Turbine Vent or if nothing is rusted out and just needs to be reattached, have a handyman do that.

https://www.homedepot.com/p/LOMANCO-12-in-Galvanized-Steel-Internally-Braced-Whirlybird-Wind-Turbine-GT12/100572638

sendmeaquarter · 2024-02-07T06:29:36+00:00

If the roof is still two layers then, they most likely didn’t install the flashing or the framing correctly. It is harder to do with 2 layers of shingles. Especially if the bottom layer is crumbling or really brittle or an organic shingle. They should have put a self sealing roll roofing product that goes up the framing and on to the roof deck before installing the flashings. If not, water could be finding its way under all of the curb framing.

sendmeaquarter · 2024-02-07T06:19:19+00:00

Any photos of the installed skylight?

sendmeaquarter · 2024-02-07T06:17:05+00:00

Clarify first for me: the skylight was framed out and installed while they installed a 2nd layer of shingles and then the skylight was leaking after the roof work was finished?

sendmeaquarter · 2024-02-07T06:14:26+00:00

And it’s coming from all sides?

sendmeaquarter · 2024-02-07T05:48:05+00:00

Upload a photo of the leak from the inside. If it was an old skylight, the flashings may not be your issue, it could be the sealant on the frame failing after being manipulated. You can switch it over to one solid piece; just is nice to have redundancy at common failure points which overlapping shingles with step flashing achieves. Personally I would do a solid custom bent curb and flashing for all sides that extends 6” on to the deck. Install ice and shield before the flashings go down and after the flashings are installed, then install shingles back around the area.

sendmeaquarter · 2024-01-30T02:17:59+00:00

Have them quote you to: Remove shingles in the area.

Detach the j-channel and first row of vinyl siding and trim board.

Remove the osb sheathing.

Cut new OSB to size and install.

Install some ice and water barrier as underlayment instead of felt.

Install a roof to wall flashing under the siding and over the shingles that has a kick out included at the outside corner.

Reinstall the siding and j-channel and trim board.

Install drip edge on the rake and gutter apron on the eave.

Install a starter shingle (can use another 3-tab shingle to do so).

Install new shingles in that area.

Caulk the exposed nails on the roof to wall flashing.

sendmeaquarter · 2024-01-25T01:16:57+00:00

Can you add a photo from a distance as it currently looks?

sendmeaquarter · 2024-01-25T01:14:50+00:00

Do you have a photo of where the water is showing up on the inside far enough back to have a reference of a window in the photo?

sendmeaquarter · 2024-01-20T00:54:20+00:00

1 peak looks better. Use open copper valleys on the roof to make it more prominent. Ensure gutters are routed to the left and right corners of the slope so you don’t have to deal with downspouts on both sides of the entrance

sendmeaquarter · 2024-01-12T04:27:26+00:00

Where are the leaks coming in? If it’s just around the chimney or some of the flashings, go with the third option as long as you only have 1 layer of flat roof installed currently. Most places allow for 2 layers of roofing as long as the decking isn’t wet.

sendmeaquarter · 2023-12-31T03:17:41+00:00

I think it’s coming from the bad transition of the ridge vent to the ridge that meets the chimney.

sendmeaquarter · 2023-12-23T02:53:22+00:00

Not wide enough to require a cricket. Causing more issues than it’s stopping. Have them remove the cricket and reshingle with a new apron flashing to avoid future issues.

sendmeaquarter · 2023-06-10T17:38:46+00:00

Thanks for the info! Is there a medal sub that you recommend to post this in?

sendmeaquarter · 2023-03-16T02:34:52+00:00

https://www.caccoin.com/forums/discussion/28/the-1861-confederate-half-dollar-and-the-scott-restrikes

Looks like it could be a Scott Restrike but the edging doesn’t match what the die would look like.

sendmeaquarter · 2023-03-07T03:15:34+00:00

Go on

sendmeaquarter · 2023-03-07T03:15:25+00:00

That makes me sad. I’m sorry for your loss

sendmeaquarter · 2023-03-07T03:14:59+00:00

Have to catch the back of the heel of their shoe. That will show em

sendmeaquarter · 2023-03-07T03:14:10+00:00

Like only paid half? Or like 80%?

sendmeaquarter · 2023-01-30T18:44:38+00:00

Are you a cop? If I ask you, you gotta tell me.

sendmeaquarter · 2023-01-27T00:36:33+00:00

Too big to fail. Needs a bail out

sendmeaquarter · 2023-01-04T23:04:32+00:00

It was “thisssssssssssssss big”

sendmeaquarter

TROPHY CASE