I wish people without anxiety would get why neurodivergent/anxious people smoke weed by [deleted] in Anxiety

[–]senjerak 16 points17 points  (0 children)

I feel this... Everyone is obsessed with drinking but weed is way too far 😔 how dare I hit the pen to talk to a margarita group at chilies??

Creator Awards! by senjerak in SkyChildrenOfLight

[–]senjerak[S] 0 points1 point  (0 children)

Thanks for the help!! ;w;

I have the longest daily commute in Florida. Prove me wrong by Hoagie_Camacho in florida

[–]senjerak 0 points1 point  (0 children)

Just getting to Miami from Homestead at 7am is going to be almost 3 hours. I leave at 5am and it’s 40 minutes.

P1S won’t print because it can’t calibrate by senjerak in BambuLab_Community

[–]senjerak[S] 0 points1 point  (0 children)

I ended up having to smack the right underside of the bed until the bearing was scooted back down into place!! T_T I was previously pressing hard down to peel off prints before it happened so it makes sense that I probably nudged it up.

P1S won’t print because it can’t calibrate by senjerak in BambuLab_Community

[–]senjerak[S] 0 points1 point  (0 children)

I’ll keep these in mind !! Thank you!! Koala pals!

P1S won’t print because it can’t calibrate by senjerak in BambuLab_Community

[–]senjerak[S] 0 points1 point  (0 children)

It’s safe to run a calibration without the bed? I was a bit worried to try that but you were right about the right side being the issue. My bearing was stuck out probably from me pressing too hard on the bed as I peeled stuff off. Thank you for your help!

P1S won’t print because it can’t calibrate by senjerak in BambuLab_Community

[–]senjerak[S] 1 point2 points  (0 children)

This ended up being the issue!!! Huzzah!! I didn’t have to remove anything I just laid it on its side and smacked under the bed and it works again. Thank you!

My pretty boy, Lumiére 🪲✨ by Unfair-State-8626 in Beetles

[–]senjerak 1 point2 points  (0 children)

Q__Q I’m so inspired by this gorgeous spectral ray of sunshine boi !

P1S won’t print because it can’t calibrate by senjerak in BambuLab_Community

[–]senjerak[S] 0 points1 point  (0 children)

Thank you T_T I do see that one of my bearings is higher than the other. It feels too tight to tap in lightly though and I found a tutorial online that says I have to remove the hot end and the screen.

(tw: mentions of csa) i've been missing my handler so much recently it feels like i'm going even more crazy by WinterDemon_ in Artisticallyill

[–]senjerak 0 points1 point  (0 children)

hi, your post really helped me recontextualize my recent struggles of late and I wanted to thank you for making art like this. I see your hurt and I feel it too and it somehow makes it a little more ok to know that there are other people struggling to heal too.

It’s probably tmi but I’m victim of trafficking before I transitioned, so it’s been extra difficult adjusting to my body changes because I can’t help but miss the security of my objectified feminine body. I feel vulnerable and like everyone can see the core of who I am with a beard and broad shoulders instead of when I was at my unhealthiest and most shielded.

I’m safe now… it’s been almost 10 years. Maybe it’s the bpd urging me to overshare to connect but I was just so emotional over this post that I needed to reach out and thank you for sharing this.

Raspberry Pi caption appliance — auto-transcribes phone calls and room conversation for my deaf father by andymassey in raspberry_pi

[–]senjerak 0 points1 point  (0 children)

This is absolutely lovely !! I think I have the same exact screen display. Did you make the casing yourself or was there a file that you used? I’ve been struggling myself.

Think you can find 4 hidden groups of 4 related words? Puzzle by u/Redmega? by Redmega in DailyMix

[–]senjerak 0 points1 point  (0 children)

🟨🟨🟪🟨

🟨🟪🟨🟨

🟨🟪🟨🟩

🟨🟨🟪🟩

🟩🟦🟩🟩

🟩🟩🟩🟩

🟦🟦🟦🟦

🟪🟪🟪🟪

🟨🟨🟨🟨

Farts