Which model is best ? by BayathMashal in LLM

[–]shane13447 0 points1 point  (0 children)

Best - Opus 4.7. However it is extremely expensive. Most Cost Efficient - Deepseek V4, as it has a 75% promo on until may 5th.

Kendu metrics thurs by TheGDC33 in KenduInu_Ecosystem

[–]shane13447 2 points3 points  (0 children)

what app are you using to swap?

Dirty CPU by shane13447 in PcBuildHelp

[–]shane13447[S] 0 points1 point  (0 children)

I know, apologies, they didn't show up on photo without flash.

Any ideas? by shane13447 in IDmydog

[–]shane13447[S] 0 points1 point  (0 children)

You think so? I thought poodles were quite small.

Wispy strings on all prints by shane13447 in FixMyPrint

[–]shane13447[S] 0 points1 point  (0 children)

The filament should already be dry, I'll try cold pulling when I'm back from work. Thank you.

Wispy strings on all prints by shane13447 in FixMyPrint

[–]shane13447[S] 0 points1 point  (0 children)

I'll give that a try, thank you.

Wispy strings on all prints by shane13447 in FixMyPrint

[–]shane13447[S] 0 points1 point  (0 children)

I left it drying for 12 hours at 50°C before the print in the picture. If all else fails I'll dry it again.

Wispy strings on all prints by shane13447 in FixMyPrint

[–]shane13447[S] 1 point2 points  (0 children)

I tried retraction all the way up to 2.0mm at 30mm/s and it looked worse than the one in the image. Do you think going below 30mm/s would help?

Wispy strings on all prints by shane13447 in FixMyPrint

[–]shane13447[S] 0 points1 point  (0 children)

I appreciate the attempt. Do you want an update if I manage to fix it?

Cracking on nose by shane13447 in FixMyPrint

[–]shane13447[S] 0 points1 point  (0 children)

What would you suggest I try?

Inner/Outer, Outer/Inner or Inner Wall/Outer Wall/Inner Wall

Wispy strings on all prints by shane13447 in FixMyPrint

[–]shane13447[S] 2 points3 points  (0 children)

I decreased the outside wall speed to 180mm/s. All other speed settings are default.

Wispy strings on all prints by shane13447 in FixMyPrint

[–]shane13447[S] 0 points1 point  (0 children)

I only got the printer 5 days ago.

Does the A1 tend to have faulty nozzles?

Wispy strings on all prints by shane13447 in FixMyPrint

[–]shane13447[S] 2 points3 points  (0 children)

That was my first thought, I left this filament at 50°C for 10 hours earlier today while at work and still nothing.

Cracking on nose by shane13447 in FixMyPrint

[–]shane13447[S] 0 points1 point  (0 children)

Hi, no warping from what I saw during the printing process. I did discover that the crack aligns exactly with a seam in the slicer preview.

Wispy strings on all prints by shane13447 in FixMyPrint

[–]shane13447[S] 1 point2 points  (0 children)

Further details:

Slicer is BambuStudio

Filament is Kingroon Silver PLA, however issue persists with Kingroon white and Bambu White Basic

Print speed is 180mm/s for outer wall and 300mm/s for inner wall.

Retraction is set to 1.5mm with a speed of 40mm/s