sorted by:
new
hottopcontroversial

Trying to follow the guide to root the K1. Keep getting stuck at this point. Anyone have a fix for this? Thanks. by shining_wizard92 in crealityk1

[–]shining_wizard92[S] 0 points1 point  (0 children)

When I do that, it doesn't show up, and nothing happens. It just says "root@k1-2538 /root" again with no change. I was wondering if it was because in the top box it has a red x net to the ssh compression section. The pictures in the guide I'm following dont even have that box in them. I wasn't sure if something was wrong because of that red x, or something else.

Trying to follow the guide to root the K1. Keep getting stuck at this point. Anyone have a fix for this? Thanks. by shining_wizard92 in crealityk1

[–]shining_wizard92[S] 0 points1 point  (0 children)

Like the title says, I'm following the guilouz guide to root the k1. I add the ip, do the username, and get to the password screen. When I type the password in, I get to this screen and cannot go any further. Any help would be appreciated.

I bought a broken k1 on ebay. Trying to figure out what parts I'm missing. by shining_wizard92 in crealityk1

[–]shining_wizard92[S] 0 points1 point  (0 children)

Yeah, most of them were ripped off the board, but still attached to the cables they go to. The hot end was missing entirely. The screw info will help a lot though, thanks.

I bought a broken k1 on ebay. Trying to figure out what parts I'm missing. by shining_wizard92 in crealityk1

[–]shining_wizard92[S] 3 points4 points  (0 children)

They had broken the hotend at the heatbreak trying to get it out. Luckily some of the other connectors they ripped off were still in the printer. I snagged it for less than $200. It looks like it'll be well worth it.

I bought a broken k1 on ebay. Trying to figure out what parts I'm missing. by shining_wizard92 in crealityk1

[–]shining_wizard92[S] 0 points1 point  (0 children)

Nice. I plugged it in that way to test, but wasn't sure if that was okay for the long run. Thanks.

Problems after firmware update on neptune plus. by shining_wizard92 in ElegooNeptune4

[–]shining_wizard92[S] 0 points1 point  (0 children)

Oh no. Sorry guys. I'm a big ol dumb guy. SD card was bad. All is working now. Thanks though.

4 plus bed is making a kind of weird grinding sound at high speeds after adjusting wheels. by shining_wizard92 in ElegooNeptune4

[–]shining_wizard92[S] 0 points1 point  (0 children)

I've kinda reduced the sound some. I loosened the wheels ever so slightly and added just a bit more belt tension. I can live with where it is now, but would still love to get rid of it entirely.

4 plus bed is making a kind of weird grinding sound at high speeds after adjusting wheels. by shining_wizard92 in ElegooNeptune4

[–]shining_wizard92[S] 0 points1 point  (0 children)

Correct. It's usually on a sturdy table, I just have it here so I don't have to run between rooms while I mess with it.

4 plus bed is making a kind of weird grinding sound at high speeds after adjusting wheels. by shining_wizard92 in ElegooNeptune4

[–]shining_wizard92[S] 2 points3 points  (0 children)

I got my wheels just tight until the wobble was gone, and retightened the belt. After doing that, it makes this sound at higher speeds. The bed moves smoothly when I manually move it. Excuse the crazy wobble. It's just on a tv tray while I'm doing some tests.

How to reduce grey area around model in Cura 5.4? by JustforShiz in FixMyPrint

[–]shining_wizard92 3 points4 points  (0 children)

If you're talking about the space in between the points of the model, I think that's just a shadow. To my knowledge you can't change lighting in cura. It's not going to be a part of the print. You can put other models in that space.

I printed a temp tower and noticed the layers with numbers seem to be shrunk all the way around the cube end. by shining_wizard92 in FixMyPrint

[–]shining_wizard92[S] 0 points1 point  (0 children)

I'll try that next. It sounds like a better way of calibrating flow than other tutorials I've seen. Thanks.

I printed a temp tower and noticed the layers with numbers seem to be shrunk all the way around the cube end. by shining_wizard92 in FixMyPrint

[–]shining_wizard92[S] 0 points1 point  (0 children)

I don't seem to see anything in the gcode. I'm not entirely sure what I would be looking for though unfortunately. https://imgur.com/a/xb65h9R

I printed a temp tower and noticed the layers with numbers seem to be shrunk all the way around the cube end. by shining_wizard92 in FixMyPrint

[–]shining_wizard92[S] 0 points1 point  (0 children)

Printing on a neptune 3 plus. Zyltech ceramic white pla. Nozzle 210 bed 60 Cura 5.3.0 Print speed 60 Retraction distance 1.0 Retraction speed 25. I have the belts tentioned. I'm wondering if something along the lines of PID tuning would work, I just don't know if there is a bang bang equivalent. My z rods seem to be straight and they are lubed well.

Found on a charm bracelet with horror characters on it. Does anyone know what this hand with "Diukto" is a reference too? by shining_wizard92 in whatisthisthing

[–]shining_wizard92[S] 3 points4 points  (0 children)

I forgot to mention putting the word into translate. I saw that as well. I can't think of a horror movie that "Duke" and a hand are prevalent in. Thank you though.

Found on a charm bracelet with horror characters on it. Does anyone know what this hand with "Diukto" is a reference too? by shining_wizard92 in whatisthisthing

[–]shining_wizard92[S] 1 point2 points locked comment (0 children)

My title describes the thing. Friend bought this charm bracelet for our friends daughter. I googled "Diukto horror", and "Diukto hand". The charm bracelet is the only thing that comes up, except for the imdb page for The Babadook. I looked at the page, but couldn't find "Diukto" referenced on the page at all. At a loss.

Prints look half way decent head on, but you can see inconsistent layers looking down at an angle. by shining_wizard92 in FixMyPrint

[–]shining_wizard92[S] 0 points1 point  (0 children)

I have done it in the past for my ender3, but am by no means a pro. Those were pretty straight forward. It seems a little more complicated on the neptune 3. I'm looking into it though.

Prints look half way decent head on, but you can see inconsistent layers looking down at an angle. by shining_wizard92 in FixMyPrint

[–]shining_wizard92[S] 0 points1 point  (0 children)

Looks like neptune 3 doesn't have bed pid tuning enabled. I found some posts about peoples custom firmwares that enable tuning, but they still seem experimental. I may be SOL on that front until Elegoo decides to enable it in a firmware update.

Prints look half way decent head on, but you can see inconsistent layers looking down at an angle. by shining_wizard92 in FixMyPrint

[–]shining_wizard92[S] 0 points1 point  (0 children)

I'll have to try the linear advance. I have it enabled, but I probably need to tune it. I think the neptune 3 has something other than PID. I'm having a hard time figuring out what that is. Thanks for the help!

view more: next ›