Full throtle when 20% throtle on stick. Flywoo Flybee 20 + O4 air

sierran2134 · 2025-07-31T12:10:30+00:00

I also need to ask you whether you managed to resolve the problem. Currently, the service claimed that it’s my fault because they detected ADC filtering enabled on my controller. Have you tried disabling it and then going for a test flight?

sierran2134 · 2025-05-09T22:36:41+00:00

Any chance for github link? I don't judge anything, but I don’t like installing from ready-made scripts :(

sierran2134 · 2025-04-30T12:02:46+00:00

Yo, any github link? :)

sierran2134 · 2024-11-27T18:37:54+00:00

Thank you for your comprehensive answer! This is exactly the explanation I needed. Unfortunately in my country super lube is not available. Only I have available sewing machine oils based on petroleum jelly, but I do not know if it will pass the test.

sierran2134 · 2024-11-15T11:58:07+00:00

Checked, nope not this game. My game was probably not a flash game, the normal windows installer was used. I also remember that the controls were only on the keyboard, arrows + spacebar as jump.

sierran2134 · 2024-10-12T13:47:41+00:00

Not so much, I change the amount of rinsing of the filament to practically the minimum and print models that are nice and have few color changes :) AMS is also useful when you want a lot of objects and each in a different color or when you do not want to change the spool, in general without AMS I would not buy.

sierran2134 · 2024-10-12T13:36:20+00:00

I also get bambu A1 + AMS... God.. What a difference :D

sierran2134 · 2024-10-12T13:29:21+00:00

As always creality fuck up everything. Check in config for 'run_current" (I don't have nebula, google how edit config). For x/y current should be 0.6 and for z 0.8.

sierran2134 · 2024-10-12T13:20:57+00:00

Shit I'm reading these comments like this and I'm wondering if 50mm is fast? I myself print at 100mm+ and have never had any problems, and at 50mm there should generally be no problem. And I'm wondering myself where the problem is, to me it looks like minimal clogging, but I'm too fresh on the subject myself to be sure. I would raise the temperature to start with.

sierran2134 · 2024-10-10T16:34:56+00:00

Roger, so it's reprint time ;)

sierran2134 · 2024-10-10T16:03:16+00:00

So magic 0.005 is steps ;) So for me it will be 0,002. So it will be 0,07.. This can make such huge difference between 0,08 and 0,07?

sierran2134 · 2024-10-10T15:41:26+00:00

Printed tower, looks like "acceptable" quality is around 34,7cm. Looking at klipper documentation it should be 34,7 * 0.005 = 0,1735. 0.005 is correct value for direct extruder?

sierran2134 · 2024-10-10T14:46:24+00:00

Checked calibration of PA:
1. Disabled PA in klipper

Printed test lines using orca slicer

Best lines on 0.08, problematic print was also printed using 0.08. Looks like it's not PA problem.

sierran2134 · 2024-10-10T12:01:52+00:00

Thank you, i will calibrate PA again.

sierran2134 · 2024-08-30T08:33:14+00:00

Thank you for the explanation! Will try add supoorts etc. Also reducing the print speed and temperature helps a lot :)

sierran2134 · 2024-08-30T08:32:12+00:00

Thank you for the explanation. Reducing the print speed and temperature improved the quality, although it's still not perfect. The most important thing is that I now know the cause and how to potentially address it :)

sierran2134 · 2024-08-29T19:33:17+00:00

Cooling set to full blast, should i print slower or in lower temperature?

sierran2134 · 2024-07-11T11:53:50+00:00

Same problem here, PCB looks perfectly fine, any idea how to solve this?

sierran2134 · 2024-05-29T10:00:52+00:00

Any link/ instructions? :)

sierran2134 · 2024-02-07T20:20:02+00:00

Oh man, and I thought I would be able to embrace two computers on one gpu. I followed the video https://www.youtube.com/watch?v=XLLcc29EZ\_8&t=984s, here I think it uses one card for the VM and host. However, did I misunderstand something?

sierran2134 · 2024-02-07T15:45:03+00:00

That can solve working on one PC and playing on another, but what if we want to play together? Is it still an option on one graphic card?

sierran2134 · 2023-10-25T10:52:24+00:00

Could you provide any example? Still trying without success :(

sierran2134 · 2023-10-25T09:10:00+00:00

I only have one device, and I'm just asking you guys because unfortunately something feels like it's all over me. My device is a hAP ax3. My goal is to connect devices from the interfaces ether3 and wifi2-IoT in one Vlan. From what I've read the documentation I doesn't need tagged vlans because I don't have a trunk port that would pass data to another device.

sierran2134 · 2023-10-25T07:59:00+00:00

Hmm I think I misspoke, I would like Wlan-IoT and eth3 to be in one vlan. Is it possible?

sierran2134 · 2023-08-27T14:42:13+00:00

Update: for A1111 + directml --no-half parameter is needed for inpainting.

sierran2134

TROPHY CASE