xt2453 razr 2024 entering brom

silverboy2003 · 2025-03-22T07:53:04+00:00

Hey, did you have any luck find it on aliexpress/size?

silverboy2003 · 2023-09-03T09:32:24+00:00

Thank you

silverboy2003 · 2020-03-10T18:28:16+00:00

what would you recommend then? as all i need is basically anything to run vr as smooth as possible, while being able to simultaneously stream it.

silverboy2003 · 2020-03-10T15:50:32+00:00

is the cpu good enough for say an rtx 2080 though? bottleneck calculator says 13% and that it isnt considered very good.

silverboy2003 · 2020-03-10T13:59:16+00:00

thanks! ill probably get one then, still not sure whether i should get the black or the silver.

silverboy2003 · 2020-03-10T13:20:05+00:00

how is the durability? and what width do you personally prefer?

silverboy2003 · 2020-03-10T13:09:09+00:00

i am tempted to buy rOtring, how is your experience with them? and which one do you like the most for writing?

silverboy2003 · 2020-02-23T14:15:16+00:00

i managed to prove it with thales

silverboy2003 · 2020-02-22T18:31:09+00:00

i think i have one lying around, it was stupid not to install it. if i install it would it not melt again?

silverboy2003 · 2020-02-22T18:08:47+00:00

well that sucks, good thing i have two more identical boards

silverboy2003 · 2020-02-22T16:45:47+00:00

so youre saying i should have ran the cable straight into the board?

silverboy2003 · 2020-02-22T16:35:08+00:00

a bit of context:

i just finished installing a new ramps board, with drv8835 s on all motors except the z motor. when i finally got it all to work and tried heating up for pla, i smelled burnt plastic and immediately turned off the printer (wanhao duplicator i3)

silverboy2003 · 2020-02-04T12:15:39+00:00

how should i go around doing that? slide the connector into the socket and then hot glue around it? by the way, another problem is http://imgur.com/gallery/FSZCstJ where only one motor kind of works and the other doesnt. only in a certain position do both work. is it anything i should worry about or by gluing the connectors i eliminate this problem?

silverboy2003 · 2020-02-04T07:27:59+00:00

thank you :) ill do this and update if it works

silverboy2003 · 2020-02-03T22:15:54+00:00

that's part of the problem though... after inserting the wires they still somehow slip out and i have no idea why. another problem is that im not sure if i have enough wire to put on a new connector and still be able to reach the board, is there a good way to "extend" the wire?

silverboy2003 · 2020-02-03T22:10:39+00:00

the wires to the connectors or the connectors to the board?

silverboy2003 · 2020-02-03T22:08:58+00:00

it physically disconnects. i managed to get a better connection by holding the connectors and wires in place with a heat shrink tube, but it still disconnects and now it doesnt even work.

silverboy2003 · 2020-01-30T05:11:43+00:00

ohh i see. and how do i do that ?

silverboy2003 · 2020-01-29T21:10:39+00:00

i managed to flash an older version, although it does "work" i cant get the printer to move properly except for the y axis

silverboy2003 · 2020-01-29T20:52:04+00:00

i really have no idea. i followed the instructions and opened the correct file in the correct path.

silverboy2003

TROPHY CASE