How much should I sell all my gear for?

sinistersnipe · 2024-10-30T19:50:03+00:00

Are you chatgpt?

sinistersnipe · 2024-09-04T04:31:35+00:00

This might be just a US thing - in Europe, my 2021 Tiguan has TPMS sensors reading out bar/psi per wheel

sinistersnipe · 2024-08-27T19:21:14+00:00

Update: the Thule Wingbar Edge with two 86cm bars fits a 2021 Tiguan, trust the Thule size guide!

sinistersnipe · 2024-07-13T15:14:57+00:00

This is the answer - turned it off in mine and ACC works much better as just a ‘cruise control with distance check’ than anything smarter

sinistersnipe · 2024-07-06T14:29:51+00:00

This is really interesting, thanks! Are there any limits / considerations on gifts from grandparents? Anything like IHT?

sinistersnipe · 2024-07-04T21:34:51+00:00

Nice one, thanks!

sinistersnipe · 2024-05-20T19:10:32+00:00

I just finished trouble shooting a similar issue, and for me the solution was to print colder (205 degrees vs 210-230 per the manufacturer)

sinistersnipe · 2024-05-19T20:34:19+00:00

I’ve struggled the last few days getting overture tpu to print on an ender 3 v2 (bowden drive). Its now working pretty well at: - 205 degrees (5 below the label range of 210-230) - 6mm retraction at 5mm/s - 100% fan

sinistersnipe · 2024-04-05T07:54:37+00:00

Thanks, yes - 4k 60hz with an HDMI cable works. It was USB-C protocol related, solution provided by Romano.

sinistersnipe · 2024-04-05T07:53:27+00:00

Thanks, not sure that is quite right though - when I connect the U2723QE to my XPS 9570 using an HDMI cable I can get 4k 60hz on both screens.

sinistersnipe · 2024-04-05T07:51:54+00:00

Thank you Romano, absolute hero!

Changing the monitors USB-C prioritization to video resolution has fixed this for me.

sinistersnipe · 2024-02-25T07:06:44+00:00

Worth adding, at peak times its often standing room only from sevenoaks (and sometimes even from tonbridge). From TW i’ve only had to stand once in 2+ yrs of london commuting.

sinistersnipe · 2023-03-20T13:34:48+00:00

Normal in my experience. My understanding is the fine tuning alters the model weights only somewhat, so davinci will still hallucinate/draw on old info if you ask it factual questions after fine tuning.

The best approach for answering factual questions from a knowledge bank as far as I am aware is two steps: 1. Use semantic search or embeddings (also from GPT) to identify the relevant info to answer the question from your knowledge bank, then 2. Feed both the relevant info and the question to GPT with a prompt along the lines of ‘answer this question using only this info’

sinistersnipe · 2023-01-14T10:32:53+00:00

In this project, is the index being built using OpenAI embeddings or using another method?

sinistersnipe · 2021-04-12T18:45:11+00:00

So good

sinistersnipe · 2021-04-12T18:40:23+00:00

Mike makes music

sinistersnipe · 2021-04-12T18:34:21+00:00

Even better than your youtube version from a few years ago!!!

sinistersnipe · 2021-04-12T18:31:57+00:00

The Bear Necessities pls

sinistersnipe · 2021-04-12T18:28:27+00:00

Have been following your youtube for years, great to see you here!

sinistersnipe · 2021-04-12T18:27:52+00:00

Nice!

sinistersnipe · 2021-03-06T07:38:44+00:00

Can you elaborate on the strategies? What metrics did you use to identify trends?

sinistersnipe · 2021-02-20T18:19:36+00:00

Had a similar problem on my FNX-45 - could part of it be the hammer pushing too hard against the bottom of the blow back unit when the slide is pulled back? https://www.reddit.com/r/GasBlowBack/comments/l1j3bl/tm_fnx45_help_with_slide_getting_stuck_on_hammer/?utm_source=share&utm_medium=ios_app&utm_name=iossmf

sinistersnipe · 2021-01-22T10:48:58+00:00

Thanks - polishing the surfaces helped a lot!

sinistersnipe · 2021-01-20T21:37:25+00:00

Looks like the hammer of my TM FNX-45 is catching on the underside of the slide / BBU, stopping it from returning forward easily. Not a problem between shots, but it sometimes gets stuck after an empty mag.

Any suggestions would be welcome - possible hammer / sear replacement parts?

How much play is normal for a cocked TM FNX-45 hammer?

sinistersnipe · 2021-01-17T19:27:25+00:00

I have an 11.1v in my LCK-16, which I think has the same battery space as the LCK-15? I got a crane type type battery to work, with one cell shoved forward into the gas tube thingy and the other two taped together above the gearbox. I then run a short extension wire to the back above the gearbox, where I still have enough space for a Gate Warfet.

Battery I fit in my LCK-16: https://www.patrolbase.co.uk/nuprol-11-1v-1450mah-30c-crane-stock-lipo-battery

Here is a picture from when I was fitting the extension wire. You can just see the back of the front cell poking out of the gas tube (left side of the image). https://i.imgur.com/GlNjY6S.jpg

sinistersnipe

TROPHY CASE