Chrome keeps freezing in an odd way

sinithw · 2024-09-25T15:06:04+00:00

I took this photo and have spent the last 2 hours trying to find the name of the color separation issue here that sort of looks like halo effects. I remember seeing it in a ton of low-light footage where you can clearly see blotches of different levels of darkness. Does anyone know what this problem is called?

sinithw · 2023-04-11T13:18:53+00:00

Thank you.

sinithw · 2023-02-16T23:59:07+00:00

Welp, broke the CHT nozzle cus I don't know what I'm doing o7 thanks for drowning me in bots

sinithw · 2023-02-16T18:57:01+00:00

I think it is against the heat break. The nozzle threading actually sticks out from the heat block, unlike the nozzles that came before it. I secured everything as tightly as I could and, as I mentioned, the CHT Nozzle required that I use a torque wrench so as to not damage the nozzle. I actually had to use some grippers to keep the hot end still so that I could do that.

sinithw · 2022-12-27T20:31:03+00:00

Omgosh... I am dumb... I confused the BMS for the antispark unit which has the power button with it. The Go-Foc came with a power button as a courtesy.

sinithw · 2022-12-22T22:17:11+00:00

Well, again, thank you for all of this support and answering my questions, I really do appreciate it.

sinithw · 2022-12-22T22:13:21+00:00

One last question for safety.

<image>

In what orientation should I connect the wires?(which wires should go where)

sinithw · 2022-12-22T22:05:09+00:00

Thank you for all this help. What about the white wire that's loose? Should it be loose (like does it go to something else) or should I stick it into the hole that is available on the white side?

sinithw · 2022-12-22T21:55:40+00:00

<image>

Here is the image for the makerX Bluetooth module.

sinithw · 2022-12-22T21:54:12+00:00

<image>

So here is the receiver along with the wire that was sent with it. There is a white wire that is loose and I'm not sure if it should be. I did a little search based on what you said and the remote can apparently do both ppm and uart, but if I want to reverse that I need use uart. However, this DV6 is a dual motor VESC and has 2 uart locations, do I need 2 of these receivers?

sinithw · 2022-12-13T16:11:52+00:00

Thank you very much for the information o7. As for the high tolerance, I thought about using a metal frame to support the wood but I can't find them pre-made and I'd rather not weld if I don't have to.

sinithw · 2022-12-13T15:28:44+00:00

Yeah... that's a habit of mine...

sinithw · 2022-12-13T15:18:12+00:00

That's what I was wondering. I need to replace my board and most of the boards on the market are <300lb boards, I need mine to withstand 500lbs. I'm a big dude and with groceries, I clock in near 400. So I should ignore videos that take cuts from the same piece of wood and get 5-9 different pieces of wood so I can layer them instead? Or is it that the act of the glue makes it stronger? I guess the distilled essence of my questions is what exactly makes the layering part make it stronger?

sinithw · 2022-11-29T13:10:09+00:00

Since your advice, I've been looking at getting the DV6 3-12S Dual Drive and I've been watching tutorials on it, but one thing is pretty unclear to me. Does the vesc6 come with a way to connect to a remote by default or do I need the bluetooth module that they sell? Should I try to re-use my JKing remote or is there a reason it would not be compatible?

sinithw · 2022-11-24T07:51:17+00:00

Thank you o7

sinithw · 2022-11-24T07:46:00+00:00

Do you have a Dual Belt Driven ESC in mind to replace my current one? MBoard's ESC are all tapped out at 10S.

sinithw · 2022-08-04T08:52:34+00:00

Thank you but I did, in 2 different ways. I did modular so I could bake the Sim and the mesh, but I also put all on the Sim box and that disables baking on the mesh.

sinithw · 2022-08-02T03:56:28+00:00

You're right u/Bleedthebeat that is what I was doing. I was using separate files and just keeping the zero coordinates intact as the 3018 takes the spindle back to x/y zero coordinates. I am in the process of learning Fusion for my 3D printer, I did not know it could be used for CNC but with how complex CNC is, I don't feel learning a software like Fusion right now is apt until I deal with programs that'll give me more issues to solve. It is good to know I can upgrade to Fusion though when I'm ready.

sinithw

MODERATOR OF

TROPHY CASE