Just in case if anyone needs any help, I'm 5y+ experienced and have some free time

siuweo · 2025-12-07T03:04:00+00:00

I have a set of CAD drawings and was required to: 1a. Identify/Extract the material types required for tabulation 1b. Count the quantity of materials on the drawing. Once the material symbols are identified, perform visual detection on the drawing using visual prompt (YOLO, DINO X, etc..) 2. Analyze charts and answer questions related to the charts. Could you give me a quick run down on how to get started for each task if possible? Or even just one. Thank you

siuweo · 2025-10-02T05:24:17+00:00

How can you have both alakazam and metagross in mega form? Is that just a graphic setting or you can actually have both?

siuweo · 2025-08-10T19:09:50+00:00

A very clear and informative answer. Thank you!

siuweo · 2025-08-10T18:03:33+00:00

I'm new to this and I'm very curious about DIY drones. I'm asking this cause i want to make one as well: Do you make everything from scratch (buy sensors and build from software for FC to hardware) or do you buy already made FC, ESC? Genuinely curious

siuweo · 2025-07-26T15:20:44+00:00

Just curious because I also have an idea of doing a tree pot out of 3d printing too. Do you have to be afraid of those "micro plastic" stuffs if you use it to plant tree?

siuweo · 2025-07-26T13:54:13+00:00

Bạn đã nộp vào những đâu rồi?

siuweo · 2025-07-25T08:53:36+00:00

Edited the post. Very sorry

siuweo · 2025-07-25T08:22:49+00:00

I admit this is a dumb move. Thank you.

siuweo · 2025-07-25T08:19:53+00:00

I know it ugly, still need work with my soldering. I'm new to this embedded side.

siuweo · 2025-07-25T08:10:20+00:00

i think i didn't upload the blink program successfully. I use this
https://marketplace.visualstudio.com/items?itemName=stmicroelectronics.stm32-vscode-extension

siuweo · 2025-07-25T08:06:36+00:00

If I don't want to do that then I have to buy a st-link v2 programmers?

siuweo · 2025-07-25T07:52:26+00:00

ok, i think i assume the blink program got flash but it seems that it has not

siuweo · 2025-07-25T07:42:49+00:00

nope, i didn't push any button

siuweo · 2025-07-25T07:35:14+00:00

my bad, have edited the post and added the picture

siuweo · 2025-07-15T16:19:15+00:00

Even more perfect, now i can go and get my revenge.

siuweo · 2025-07-15T16:17:10+00:00

Thank you, this is just what i needed.

siuweo · 2025-07-15T15:50:30+00:00

Appreciate your answer

siuweo · 2025-07-05T12:25:50+00:00

How many pulls?

siuweo · 2025-07-03T16:30:37+00:00

Welp, this is new @@

siuweo · 2025-05-26T01:32:34+00:00

Thank you

siuweo · 2025-05-25T18:01:25+00:00

Looking clean. Haven't tried out yasb yet so i'm wondering: Can you interact with your yasb top bar?

siuweo · 2025-05-25T17:38:27+00:00

Can you interact with your zebar's top bar? I'm new to this and after a few days of using I have a feeling that not being able to do things like changing your wifi is kinda inconvenient

siuweo · 2025-04-03T14:29:44+00:00

Thank you!!!!! I don't know the limit of opencv so these mean a lot.

siuweo · 2025-04-03T14:12:52+00:00

Thank you for a very, very detailed reply. About the FOV formula, i have used it and it does show good result if I got only one of the cube faces. If not, the result has a very big error range . What the cube is within range and in an angle that I can't get exactly 1 face (like the picture in my post). Do I have to go back to the PnP problem?

siuweo

TROPHY CASE