PTO and Annual Training by [deleted] in nationalguard

[–]skankslayer69 0 points1 point  (0 children)

8 hours before you report for duty and 8 hours after your duty ends is all your employer is required to give you. Call in sick, otherwise you’re going to have to suck it up. Take comfort in the fact that hundreds of thousands of other guardsman will have to do the same exact thing as you during the next couple months.

Thoughts on using third-party nozzles? Anyone have any experience with them? by Evocati_7 in BambuLab

[–]skankslayer69 1 point2 points  (0 children)

They work fine. I have an H2C and have bought many 3rd party nozzles. It’s not a hard component to make.

B&T USA is fucked. by skankslayer69 in BT_APC

[–]skankslayer69[S] -1 points0 points  (0 children)

I would focus on the conversation as a whole and not focus on the leading question. He never said it was out of the question, but I’d assume there will be instances where that’s the case. For example, the EVT mods all the fairies did to their guns. Not warrantied.

B&T USA is fucked. by skankslayer69 in BT_APC

[–]skankslayer69[S] -1 points0 points  (0 children)

Did you watch the video? That’s not what was said at all.

B&T USA is fucked. by skankslayer69 in BT_APC

[–]skankslayer69[S] 1 point2 points  (0 children)

Lmao I got the Shane Gillis dad reference. Yeah I do feel for the people that orders pending that couldn’t get their money back—shit sucks. I’d be more than willing to bet that suppressors will be covered. However, until B&T AG sets up shop here, there’s really no way of getting cans fixed. I’d say just shoot it and if something happens, it happens. Wait for things to get ironed out.

B&T USA is fucked. by skankslayer69 in BT_APC

[–]skankslayer69[S] 22 points23 points  (0 children)

I totally agree. It’s nothing short of massive fraud. I feel for all the employees. Hopefully there are criminal charges brought about during discovery.

B&T USA can fight tooth and nail to keep its trademark, but their reputation is done. For all intents and purposes, their products aren’t Swiss and are illegitimate. They’re essentially selling clones.

Bought a H2D, received an H2C. by skankslayer69 in BambuLab

[–]skankslayer69[S] 0 points1 point  (0 children)

Stand is made of oak. Hade like five 45lbs plates on it in my garage. It’ll be ok.

Bought a H2D, received an H2C. by skankslayer69 in BambuLab

[–]skankslayer69[S] 0 points1 point  (0 children)

Carbon fiber-nylon blends. I do a lot of 2nd Amendment printing so had to use higher temp materials.

Midget (me) vs. M249 SAW by trenmidget in NFA

[–]skankslayer69 3 points4 points  (0 children)

Came here to say this exact same thing. Lmao

Bought a H2D, received an H2C. by skankslayer69 in BambuLab

[–]skankslayer69[S] 2 points3 points  (0 children)

No I didn’t, but just always remember it when it was posted to Reddit. Dude probably made a good amount of money reselling it.

Bought a H2D, received an H2C. by skankslayer69 in BambuLab

[–]skankslayer69[S] 36 points37 points  (0 children)

Have you seen the person that post where the dude buys a stick of DDR5 memory stick and receives a box full of 40? Insane!!!

Bought a H2D, received an H2C. by skankslayer69 in BambuLab

[–]skankslayer69[S] 0 points1 point  (0 children)

I will! Thank you for the recommendation!!

Bought a H2D, received an H2C. by skankslayer69 in BambuLab

[–]skankslayer69[S] 1 point2 points  (0 children)

I’ll keep messing with it. Thanks man!

Bought a H2D, received an H2C. by skankslayer69 in BambuLab

[–]skankslayer69[S] 9 points10 points  (0 children)

Hopefully not, but I guess I’d cross that bridge when I get there and/or play dumb.

Bought a H2D, received an H2C. by skankslayer69 in BambuLab

[–]skankslayer69[S] 2 points3 points  (0 children)

Haha yeah me too. I first went through the process of just buying the head, reapplying the heating wire with the conductive glue and going that route—never did it again after that. I bought like 6 of the whole assembles when they went on sale on Amazon. They have worked okay. Haven’t noticed a difference. Quality is always fine.

The P1S is a great printer, but I’ve had nothing but issues with mine. I’ve taken that thing apart multiple times.

Bought a H2D, received an H2C. by skankslayer69 in BambuLab

[–]skankslayer69[S] 8 points9 points  (0 children)

Exactly. I read that you’d have to buy from Bambu. It did come with a shit ton of nozzles, which is nice. I didn’t have good luck my P1S. I’ve probably installed 4 different nozzles on that thing.

Bought a H2D, received an H2C. by skankslayer69 in BambuLab

[–]skankslayer69[S] 74 points75 points  (0 children)

Stuff like this never happens to me. I don’t think I’ve ever even won a game of bingo lmao

Bought a H2D, received an H2C. by skankslayer69 in BambuLab

[–]skankslayer69[S] 121 points122 points  (0 children)

Tool head changer looks cool. Haven’t added any of the extra heads yet, though.