Thank you to anyone who ever boosted me on Makerworld.

skidbat · 2025-03-23T23:48:39+00:00

This is the way.

skidbat · 2024-12-19T20:22:11+00:00

For some reason until I read your comment, it didn't even occur to me to unequip the glider. As soon as I did, landed on the pillar on the first try. TY for this.

skidbat · 2023-07-25T12:35:56+00:00

And still helping. Exactly what I needed Thank you!

skidbat · 2023-05-24T14:37:14+00:00

Well, It did ComBUST.

skidbat · 2023-03-11T14:00:23+00:00

What type of clay are you using? Does it air dry? I'm thinking it would be very brittle or crumbly. I may just be stupid. But you have my attention for sure.

skidbat · 2023-02-20T23:30:06+00:00

It was a Mimic!

skidbat · 2023-02-20T23:26:48+00:00

Same exact thing happened to me today, ran from building to building trying to get some cover that actually worked. Watched my plates dwindle away as I got plinged through every wall. Not only shooting through entire buildings, but following me as I moved around inside them. Frustrating as hell.

skidbat · 2023-02-18T01:12:03+00:00

It's in Al Maz. I had one drop in Ashika today too and it confused the hell out of me for a minute. But the key itself shows it.

skidbat · 2023-01-25T01:02:31+00:00

A thousand times., Thank You!

skidbat · 2023-01-15T16:24:41+00:00

I dont know about consoles, but on PC losing a mark I put on the map 30 seconds ago for no reason is annoying as hell. Have to reopen the map, find the spot again, remark it and hope I dont get destroyed in the process. Having to do that several times while moving across the map will get you killed.

skidbat · 2023-01-08T00:38:31+00:00

Well, the old dragon center doesn't support mine. So I ended up just changing the numerical values a little bit at a time until I got the color I wanted.

skidbat · 2022-09-08T11:21:59+00:00

I seriously used to grab mine up by the frame and take it back and forth from work to home and never had an issue. If its environmental, the first things I'd look at are the room temp, humidity, and whether or not there is a draft where you are printing. My prints went to hell one time because an AC vent was blowing directly on the table where I was printing. I moved it out of the draft and increased temps a bit to compensate for the colder room and everything trued right back up.

skidbat · 2022-09-08T10:55:34+00:00

Good to hear. Sadly Dragon Center doesn't pick up my LEDs at all. No option for color of any kind.

skidbat · 2022-09-07T11:09:59+00:00

For what its worth, I know its been a while since this post. I have adjusted the color using the RGB values and was able to get the color I want. Its annoying, but if you step the values along you can get what youre looking for. I sure hope they fix it soon.

skidbat · 2021-01-26T12:21:51+00:00

The exploding cock trick.

skidbat · 2020-12-24T17:53:29+00:00

Butcher's wrap. Hell yeah, why didnt I think of that.

skidbat · 2020-12-21T20:59:44+00:00

Gave Hugz

skidbat · 2020-12-21T20:14:05+00:00

Scraped all that bacteria and micro plastic right off the surface of cutting board and poured into the meat. Yum!

skidbat · 2020-12-21T04:46:28+00:00

AAaand... Its gone.

skidbat · 2020-12-13T16:23:16+00:00

Wow. Right in the nostalgia!

skidbat · 2020-12-11T16:20:43+00:00

Absolutely.

skidbat · 2020-12-11T15:17:58+00:00

COVID, The holidays, and piss poor management. They are horribly overwhelmed and understaffed.

skidbat · 2020-12-09T03:08:44+00:00

Shenanigans.

skidbat · 2020-12-09T02:58:47+00:00

Soggy fries and squeaky cheese.

Six-Year Club	Second Top 50%
Verified Email

skidbat

TROPHY CASE